Roland RD-600 - Page 65

NRPN Data entry
MSB LSB MSB Description
OTE 201 mmit TVF cutoff frequency (relative change on specified channel)
mm: 0EH-~IQH-72H (-50 - 0 - +50)
(UH 63H mmH
channel}
TVF&TVA Env. Attack time (relative change on specified
mm: DEH-10H-72H (-50 - 0 - +50)
O1H 64k mmH
nel}
TVF&TVA Env. Decay time (relative change on specified chan-
mov. NEH-4OQH-72H (-50 - 0 - +50)
OPH 66H mm
channel}
TVF&TVA Env. Release time (relative change on specified
mm: JEH-JOH-72H (-50 - 0 - +50)
Parameters marked “relative change” will change relative to the preset value.
) RPN MSB/LSB (Controller number 100, 101)
Status Indbyie ed byte
8nH ASH mmlt
Bn osH nH
n= MIDI channel number: OH-FH {ch.1-ch.16)
mm = upper byle of parameter number specified by RPN
{= lower byte of parameter number specified by RPN
* The value specified by RPN will not be reset even by messages such as Program
Change or Reset All Controller.
"RPN**
The RPN (Registered Parameter Number) messages are expanded control changes, and
each function ot an RPN is described by the MIDI Standard.
To use these messages, you must first use RPN MSB and RPN LSB messages to specify the
parameter to be controlled, and then use Data Entry messages to specify the value of the
specified parameter. Once an RPN parameter has been specified, all Data Entry messages
received on that channel will modify the value of that parameter. To prevent accidents. it
is recommended that you set RPN Null (RPN Number = 7FH/7FH) when you have fin-
ished setting the value of the desired parameter.Refer to Section 4. “Examples of actual
MIDI messages” <Example 4> (page 72).
On the RD-600, RPN can be used to modify the following parameters.
RPN Data entry
MSBLSB = MSBLSB Explanation
OOH NOL T mmHi— Pitch Bend Sensitivity
mm: 0OH-0CH (0-12 semitones), Initial Value = 02H (2 semi-
tones)
I: ignored (processed as 00H)
specify up to 1 octaves in semitone steps
The Bend Range Up parameter, Bend Range Down parameter
will also be changed
OOLL OTH mmH IH Master Fine Tuning
mm, tH: 20 00H - 40 00H - 60 00H (-50 - 0 - +50 cents), Initial
Value = 40 00H (40 cent)
When this message is received on Rx Part MIDI Channel, it
will be added to Master Tune and the Fine Tuning will change.
tf Control Channel matches the Rx Part MIDI Channel, the
Master Tune setting will change
00H 92H mm — Master Coarse Tuning
mm: 10H-40H-70H (-48 - 0 - +48 semitones), Initial Value =
40H (29 semitone}
i ignored (processed as 00H)
The Coarse Tune of lone parameter will be changed
TPH 7FH 0 RPN null
Set condition where RPN and NRPN are unspecified. The data
entry messages after set RPN null will be ignored. (No Data
entry messages are required after RPN null):
Settings already made will not change.
mm, th ignored
@ Program Change
Status 2nd byte
Cah ppH
OH-FH (ch.}-ch. 16)
OOH-7 FL (prog.1-prog. £25}
n= MIDI channel number:
pp = Program number:
* Not received when Rx. PROGRAM CHANGE = OFF. (Initial value is ON)
After a Program Change message is received, the sound will change beginning with
the next Note-on. Voices already sounding when the Program Change message was
received will not be affected.
@ Pitch Bend Change
Status 2ndbyte 3rd. byte
EnH NH mmH
OH-FH (ch.t-ch.16)
(0 OOH - 40 00H - 7F 7FH (-8192 - 0 - +B19T)
n = MIDI channel number:
mm, Il = Pitch Bend value:
Not received when Rx.PI1CH BEND = OFF, (Initial value is ON)
lH Channel Mode Messages
@ All Sounds Off (Controller number 120)
Status Zodbyte Sed. byte
Bnit 78H OO
n= MIDI channel number : OH-FH (ch.I-ch.16)
When this message is received, all currently-sounding notes on the corresponding,
channel will be turned off immediately.
@ Reset All Controllers (Controller number 121)
BnH 79H OOH
n= MIDI channel number :HH-FH (ch.1-ch.16)
When this message is received, the following controllers will be set to their reset val-
ues.
Controller Reset value
Pitch Bend Change £0 (center)
Modulation O(off}
Expression 127 (max)
Hold 1 Oo)
Sostenuto Oloff)
Soft 0 (off)
RPN unset; previously set data will not change
NRPN unset; previously set data will not change
@ All Notes Off (Controller number 123)
Status 2nd byte Jed byte
Bnil 7BH OOH
n= MIDI channel number : OH-FIH (ch.}-ch.16)
When All Notes Off is received, all notes on the corresponding channel will be turned
off. However if Hold 1 or Sostenuto is ON, the sound will be continued until these are
turned off.
@ OMNI OFF (Controller number 124)
Status 2ndbyte 3rd byte
BnH 7CH 00H
n= MIDI channel number : OH-FH (ch.}-ch.16)
The same processing will be carried out as when All Notes Off is received.
65