Royal Sovereign RSH-1151 User Manual (English)

Other manuals for Royal Sovereign RSH-1151

Questions and Answers:

D
deborahwilliamsAug 19, 2025
What to do if the Royal Sovereign RSH-1151 Laminator rollers are not running?
- C
  Connie WeissAug 19, 2025
  If the rollers on your Royal Sovereign laminator aren't running, several issues could be the cause: * Check the power connection to ensure it's properly plugged into a working outlet (220V, 15Amp, & single phase). * Disengage any emergency switches by rotating the knobs clockwise. * Make sure the paper guide and front table are correctly positioned to engage their respective switches. * Verify the safety cover is closed and its switch is engaged. Also, check for jammed film, disconnected motor wires, or blown fuses, replacing or reconnecting as necessary. In some cases, the main motor or PCB may be defective and require replacement.
M
Mary SmithAug 21, 2025
What to do if my Royal Sovereign RSH-1151 is not heating up?
- D
  Don EvansAug 21, 2025
  If the Royal Sovereign Laminator is not heating up, first ensure that it is not in “COLD” mode; switch it to “HOT” mode. If it is already in HOT mode, the set temperature might be lower than the room temperature. In this case, raise the temperature according to the recommended film temperature.
C
Christian ObrienAug 23, 2025
Why are the rollers not turning on my Royal Sovereign RSH-1151 Laminator?
- D
  Dawn HoAug 23, 2025
  If the rollers of your Royal Sovereign Laminator are not turning after pressing the “RUN” button, there might be several reasons: 1. The emergency switch might be engaged. Disengage the emergency switch. 2. The safety cover might not be closed. Close the safety cover to activate the safety switch. 3. The paper guide might not be installed correctly. Properly install the paper guide so that the micro switch is activated. 4. The motor fuse might be blown. Replace the motor fuse.
V
victoriariveraAug 26, 2025
What to do if Royal Sovereign RSH-1151 Laminator rollers are not running?
- M
  Michael ChambersAug 26, 2025
  If the rollers on your Royal Sovereign Laminator aren't running, check the following: * Ensure the power plug is connected to a 220V, 15Amp, single-phase outlet. * Disengage the emergency switches by rotating them clockwise. * Properly position the paper guide and front table to engage their respective switches. * Close the safety cover. * Un-jam any film using the pressure lever and reverse button. * Check the motor wire connections. * Replace the motor fuse if it's blown. If these steps don't resolve the issue, the main motor or PCB may be defective and need replacement.
L
Linda WilsonAug 28, 2025
How to fix Royal Sovereign Laminator rollers not heating?
- J
  Jennifer HartAug 28, 2025
  If the rollers on your Royal Sovereign laminator are not heating, the issue might be due to the laminating mode. Make sure the laminating mode is set to 'Hot' and not 'Cold' by pressing the 'C/HOT' button. Other potential causes include disconnected heating wires, a blown fuse (T/Fuse wire), a defective Bi-Metal, a defective heater (test with a multi-meter for continuity), or a defective Main PCB. Replace the corresponding part if necessary.
J
Jessica WilkinsAug 30, 2025
What to do if Royal Sovereign RSH-1151 Laminator rollers are overheating?
- P
  Patrick FieldsAug 30, 2025
  If the rollers of your Royal Sovereign laminator are overheating, one potential cause is that the wires for the lower and upper heat sensors are reversed on the main PCB; in this case, reverse the heat sensors. Other possible causes include a defective T/Fuse wire (replace it), a defective heater (test continuity and replace if necessary), or a defective Main PCB (replace it).
A
ahayesSep 2, 2025
How to fix unclear lamination on Royal Sovereign RSH-1151?
- N
  Natalie NicholsSep 2, 2025
  If your Royal Sovereign Laminator produces unclear lamination, it might be due to the main roller temperatures being too low or the lamination speed being too fast. Try raising the roller temperatures and/or lowering the lamination speed.
O
orozcotrevorSep 4, 2025
What to do if Royal Sovereign RSH-1151 is curling lamination?
- G
  ginawolfSep 4, 2025
  If your Royal Sovereign Laminator is producing curled lamination, and the lamination is curling upward, loosen the top roll film tension. If the lamination is curling downward, loosen the bottom roll film tension.
J
Jason LopezSep 6, 2025
Why are the Royal Sovereign Laminator rollers not heating up?
- I
  Ian BowersSep 6, 2025
  If the rollers on your Royal Sovereign Laminator are not heating, several factors could be the cause. First, ensure the laminating mode is set to “Hot” and not “Cold”. Other potential issues include: * Heating wire not connected to the main PCB: Connect the upper and lower heating wires to the main PCB. * Blown fuse: Replace the T/Fuse wire located on the left-hand side. * Defective components: Replace the Bi-Metal, heater (after testing continuity with a multi-meter), or the Main PCB if necessary.
J
Janet WilcoxSep 8, 2025
Why Royal Sovereign Laminator has no main power?
- S
  Shawn HallSep 8, 2025
  If your Royal Sovereign Laminator has no main power, start by checking the basics: ensure the outlet has electricity and the circuit breaker is functioning. Verify the power source is 220V, 15Amp, and single phase. If power is available, replace the main fuse located above the main power switch. Also, check that the main power wires are properly connected. If the problem persists, the transformer may be defective and require replacement.