Salda SMARTY XP User Manual

2 | EN SMARTY v2023.1
1. CONTENTS
2. SYMBOLS AND MARKING 4
3. SAFETY INSTRUCTIONS AND PRECAUTIONS 5
4. INFORMATION ABOUT THE PRODUCT 6
4.1. DESCRIPTION 6
4.2. DIMENSIONS AND WEIGHT 7
4.3. TECHNICAL DATA 10
4.4. OPERATING CONDITIONS 11
4.5. STANDARD PACKAGE OF COMPONENTS 11
4.6. DESCRIPTION OF COMPONENTS 12
5. INSTALLATION 13
5.1. RECEPTION OF GOODS 13
5.2. TRANSPORTATION AND STORAGE 13
5.3. UNPACKING 13
5.4. PIPING AND INSTRUMENTATION DIAGRAM 14
5.5. MOUNTING 16
5.5.1. UNIT PLACING AND MOUNTING POSITIONING REQUIREMENTS 17
5.5.2. CEILING-MOUNTING OF THE UNIT (SMARTY XP) 18
5.5.3. FLOOR MOUNTING (SMARTY XV) 18
5.5.4. WALL-MOUNTING OF THE UNIT (SMARTY XV) 18
5.5.5. DRAINAGE (SMARTY XV) 19
5.6. CONNECTION OF THE AIR DUCT 19
5.7. CONNECTION OF THE UNIT TO ELECTRIC NETWORK 21
5.8. START-UP RECOMMENDATIONS 21
5.8.1. SYSTEM PROTECTION 21
5.8.2. PRE-STARTUP RECOMMENDATIONS OF THE UNIT (IN THE PRESENCE OF THE END-USER) 21
6. MAINTENANCE 22
6.1. SAFETY INSTRUCTION 22
6.2. GENERAL RECOMMENDATIONS FOR THE MAINTENANCE OF VENTILATION SYSTEM 22
6.3. COVER OPENING 22
6.4. FILTERS MAINTENANCE 23
6.5. HEAT EXCHANGER MAINTENANCE 23
6.6. FAN MAINTENANCE 24
6.7. BYPASS DAMPERS AND PRE-HEATER (VERSION 1.1) MAINTENANCE 26
6.8. CONTROL BOARD MAINTENANCE 28
7. CONTROL 30
7.1. DEVICE CONTROL 30
7.2. DEVICE FUNCTIONS 30
8. CONNECTION OF ACCESSORIES 31
8.1. HEATER AND PRE-HEATER 31
8.1.1. VERSION 1.1 31
8.1.2. VERSION 1.2 33
8.1.3. VERSION S300 36
8.1.3.1. HEATER 36
8.1.3.2. PREHEATER 36
8.2. FIRE PROTECTION SIGNAL INPUT (FIRE PROTECTION INPUT (NC)) (VERSION 1.1 / 1.2) 37
8.3. FIRE PROTECTION SIGNAL INPUT (VERSION S300) 37
8.4. EXTERNAL CO
2
/RH SENSORS (VERSION 1.1 / 1.2) 38
8.5. ROOM CO
2
TRANSMITTER INSTALLATION RECOMMENDATION 38
8.6. CO
2
CONCENTRATION ACCORDING TO PETTENKOFER LIMIT 39
8.7. CONNECTION OF SUPPLY AND EXHAUST AIR DAMPERS (VERSION 1.1 / 1.2) 39
8.8. OUTSIDE AIR DAMPERS (VERSION S300) 39
8.9. CONNECTION OF REMOTE CONTROL PANEL, KNX ROOM SENSORS AND MODBUS (VERSION S300) 39
8.10. CONNECTION OF REMOTE CONTROL PANEL OR MODBUS (VERSION 1.1 / 1.2) 40
8.11. FIREPLACE PROTECTION/SYSTEM MODE SWITH/RAPID VENTILATION SWITCH INPUT (VERSION S300) 40
8.12. OPERATION INDICATION OUTPUT (VERSION S300) 41
8.13. ALARM INDICATION OUTPUT (VERSION S300) 41
8.14. FIRE PLACE PROTECTION (VERSION 1.1) 41
8.15. RECOMMENDED SCHEMES FOR CONNECTION OF INTERNAL AND EXTERNAL COMPONENTS 42

Salda SMARTY XP Specifications

General

Brand	Salda
Model	SMARTY XP
Category	Air Handlers
Language	English