Salda SMARTY XP - Heater;Pre-heater and Input Configuration

EN | 51SMARTY v2023.1
10.2. HEATER
,QRUGHUWRFRQWUROHOHFWULFDOKHDWHULWKDVWREHFRQ¿JXUHGE\IROORZLQJVWHSV
•In CONFIGURATIONZLQGRZVHOHFWONLINE CONFIGURATION BASIC and press OKRQZDUQLQJ:DLWIRUWKHGHYLFHWRVZLWFKLQFRQ¿JXUDWLRQPRGH
•Set HEATING COIL parameter to ELECTRIC HEATING COIL 21Y.
• Press APPLY – RESTART DEVICEEXWWRQDQGZDLWIRUFRQ¿JXUDWLRQWREHDSSOLHG$IWHUFRQ¿UPDWLRQRIVXFFHVVIXOGHYLFHDFWLYDWLRQSUHVVDONE.
•In CONFIGURATIONZLQGRZVHOHFWONLINE CONFIGURATION EXTENDED and press OKRQZDUQLQJ:DLWIRUWKHGHYLFHWRVZLWFKLQFRQ¿JXUDWLRQPRGH
• Select Q1 as ELECTRIC HEATING COIL COMMAND, X8 as HEATING COIL OVERTEMPERATURE DETECTOR and A3 as HEATING COIL ELECTRIC POSITION.
• Press APPLY – RESTART DEVICEEXWWRQDQGZDLWIRUFRQ¿JXUDWLRQWREHDSSOLHG$IWHUFRQ¿UPDWLRQRIVXFFHVVIXOGHYLFHDFWLYDWLRQSUHVVDONE.
10.3. PREHEATER
,QRUGHUWRFRQWUROHOHFWULFDOSUHKHDWHUZKLFKKDVEHHQFRQQHFWHGDVUHTXLUHGLQVHFWLRQ"8.1.3.2. PREHEATER"LWKDVWREHFRQ¿JXUHGE\IRO-
ORZLQJVWHSV
•In CONFIGURATIONZLQGRZVHOHFWONLINE CONFIGURATION BASIC and press OKRQZDUQLQJ:DLWIRUWKHGHYLFHWRVZLWFKLQFRQ¿JXUDWLRQPRGH
•Set PREHEATING COIL parameter to ELECTRIC PREHEATING COIL 21Y.
• Press APPLY – RESTART DEVICEEXWWRQDQGZDLWIRUFRQ¿JXUDWLRQWREHDSSOLHG$IWHUFRQ¿UPDWLRQRIVXFFHVVIXOGHYLFHDFWLYDWLRQSUHVVDONE.
•In CONFIGURATIONZLQGRZVHOHFWONLINE CONFIGURATION EXTENDED and press OKRQZDUQLQJ:DLWIRUWKHGHYLFHWRVZLWFKLQFRQ¿JXUDWLRQPRGH
• Select Q1 as ELECTRIC PREHEATING COIL COMMAND, X8 as SUPPLY AIR TEMP. AFTER PREHEATING COIL, B1 as OUTSIDE AIR TEMPERATURE, A3 as
PREHEATING COIL ELECTRIC POSITION and X3 as PREHEATING COIL OVERTEMPERATURE DETECTOR.
• Press APPLY – RESTART DEVICEEXWWRQDQGZDLWIRUFRQ¿JXUDWLRQWREHDSSOLHG$IWHUFRQ¿UPDWLRQRIVXFFHVVIXOGHYLFHDFWLYDWLRQSUHVVDONE.
10.4. SMOKE DETECTOR
%\GHIDXOWVPRNHGHWHFWRULQSXWLVDFWLYDWHGDQGFRQ¿JXUHGDVNOLQSXW,QRUGHUWRXVHD1&VZLWFKLQSXWPXVWEHUHFRQ¿JXUHGWR1&E\IROORZLQJ
steps:
•In CONFIGURATIONZLQGRZVHOHFWONLINE CONFIGURATION EXTENDED and press OKRQZDUQLQJ:DLWIRUWKHGHYLFHWRVZLWFKLQFRQ¿JXUDWLRQPRGH
• Select D1 as SMOKE EXTRACTION NORMALLY CLOSED.
10.5. FIREPLACE PROTECTION, SYSTEM MODE SWITCH OR RAPID VENTILATION SWITCH INPUT
,QRUGHUWRFRQ¿JXUH'LQSXWDV)LUHSODFHSURWHFWLRQ
•In CONFIGURATIONZLQGRZVHOHFWONLINE CONFIGURATION EXTENDED and press OKRQZDUQLQJ:DLWIRUWKHGHYLFHWRVZLWFKLQFRQ¿JXUDWLRQPRGH
• Select D2 as FIREPLACE VENTILATION INPUT.
6\VWHPPRGHVZLWFKIXQFWLRQFDQEHXVHGWRHQDEOHRQHSUHVHOHFWHGV\VWHPPRGH6\VWHPPRGHIRUWKLVVZLWFKFDQEHVHWE\IROORZLQJVWHSV
•In CONFIGURATIONZLQGRZVHOHFWONLINE CONFIGURATION EXTENDED and press OKRQZDUQLQJ:DLWIRUWKHGHYLFHWRVZLWFKLQFRQ¿JXUDWLRQPRGH
• Select D2 as one of the selections available:
1. INPUT ROOM OPERATING MODE COMFORT;
2. INPUT ROOM OPERATING MODE ECONOMY;
3. INPUT ROOM OPERATING MODE UNOCCUPIED;
4. INPUT ROOM OPERATING MODE PROTECTION.
5DSLGYHQWLODWLRQVZLWFKIXQFWLRQFDQEHXVHGWRERRVWIDQVSHHG,QRUGHUWRFRQ¿JXUH'LQSXWDV5DSLGYHQWLODWLRQVZLWFK
•In CONFIGURATIONZLQGRZVHOHFWONLINE CONFIGURATION EXTENDED and press OKRQZDUQLQJ:DLWIRUWKHGHYLFHWRVZLWFKLQFRQ¿JXUDWLRQPRGH
• Select D2 as RAPID VENTILATION INPUT.
After D2LQSXWLVFRQ¿JXUHGSUHVVAPPLY – RESTART DEVICEEXWWRQDQGZDLWIRUFRQ¿JXUDWLRQWREHDSSOLHG$IWHUFRQ¿UPDWLRQRIVXFFHVVIXOGHYLFH
activation press DONE.