Samsung SCA20 - Page 37

Alignment and adjustment
Samsung Electronics 5-7
SAC20 SCA23
MODE OSD DATA1 DATA2 DATA1 DATA2 NAME OF ADJUSTMENT
A0 O2 O2 O2 O2 W/B SD/3+AEAVR-MAXDETE
A1 90 90 90 90 W/B CONTROL BOUNDARY
A2 A6 A6 A6 A6 W/B CTL STOP HALL OF MACRO AREA
A3 43 43 43 43 W/B OUTDOOR STOP HALL
A4 00 00 00 00 R/B CTL SPEED UP/DOWN MODE
A5 FF FF FF FF NOT USED
A6 FF FF FF FF NOT USED
A7 20 20 20 20 W/B STABLE CONDITION
A8 FF FF FF FF NOT USED
A9 FF FF FF FF NOT USED
AA 0E 0E 0E 0E FOCUS RESET POSITION L
AB 11 11 11 11 FOCUS RESET POSITION H
AC 4B 4B 4B 4B ZOOM RESET POSITION L
AD 12 12 12 12 ZOOM RESET POSITION H
AE 83 83 83 83 ZOOM RESET DIFERRENCE
AF 40 40 40 40 AF FILTER1 DATA MAGNIFY RATO
B0 C0 C0 C0 C0 FILTER1 NOISE LEVEL(L) OF AREA1
B1 OO OO OO OO FILTER1 NOISE LEVEL(H) OF AREA1
B2 C0 C0 C0 C0 FILTER1 NOISE LEVEL(L) OF AREA2
B3 O2 O2 O2 O2 FILTER1 NOISE LEVEL(H) OF AREA2
B4 90 90 90 90 FILTER2 NOISE LEVEL(L) OF AREA1
B5 OO OO OO OO FILTER2 NOISE LEVEL(H) OF AREA1
B6 E0 E0 E0 E0 FILTER2 NOISE LEVEL(L) OF AREA2
B7 01 01 01 01 FILTER2 NOISE LEVEL(H) OF AREA2
BA 30 30 30 30 CHROMA SUPRESS START AGC
BE A0 A0 A0 A0 AE TAGET OF NEGA MODE(FADE IN)
BF FF FF FF FF NOT USED
C0 2A 2A 2A 2A FADE LIMIT OF NEGA MODE
C1 28 28 28 28 DATA CONTROL BOUNDARY OF OUTDOOR
C2 24 24 24 24 NEGA MODE W/B R-CONTROL DATA
C3 C1 C1 C1 C1 FOCUS RETURN LOW BYTE
C4 14 14 14 14 FOCUS RETURN HIGH BYTE
C5 42 42 42 42 ZOOM RETURN LOW BYTE
C6 12 12 12 12 ZOOM RETURN HIGH BYTE
C7 O5 O5 O5 O5 LENS CHECK MARGIN (WIDE)
C8 12 12 12 12 LENS CHECK MARGIN (TELE)
C9 65 65 65 65 ADJUST MODE IRIS SETTING DATA
CA 80 80 C0 CO D ZOOM RAITO
CB FF FF FF FF NOT USED
CC 00 00 00 00 SETUP ADJUST ENABLE
D1 FF FF FF FF HALL AUTO CHECK
D2 FF FF FF FF AGC AUTO CHECK
D3 FF FF FF FF LENS CHECK OF PCB LINE
D4 FF FF FF FF GYRO SENSOR CHECK (H)
D5 FF FF FF FF GYRO SENSOR CHECK (V)
D7 01 01 01 01 ZOOM/FOCUS CHECK ENABLE
D8 20 20 20 20 VR ZOOM CENTER MARGEIN
D9 00 00 00 00 COLOR GAIN ADJUST
DA 7E 7E 7E 7E SETUP AUTO ADJUST
DB O8 O8 O8 O8 HALL CHECK THRESHOULD
DC 82 82 82 82 COLOR ADJUST TARGET VALUE
DD 89 89 89 89 HALL ADJUST GAIN TARGET
DE 4D 4D 4D 4D HALL ADJUST CENTER
DF 00 00 00 00 NOT USED
E0 FF FF FF FF NOT USED
E1 FF FF FF FF NOT USED
E2 FF FF FF FF NOT USED
E3 FF FF FF FF NOT USED
E4 FF FF FF FF NOT USED
E5 FF FF FF FF NOT USED