What to do if a Samsung SRD-470D does not recognize all installed HDDs?
If your Samsung DVR isn't recognizing all the installed HDDs, try again after a moment. If the problem persists, it might be due to a mechanical error with the HDD. Try using a different HDD to see if that resolves the issue.
Why doesn't the Channel button work on the Live screen of my Samsung DVR?
The Channel button on your Samsung DVR's Live screen won't work if the current screen is in event monitoring mode. To exit this mode, press the [ALARM] button, then select a channel.
How to release the alarm on a Samsung SRD-470D?
To release the alarm on your Samsung DVR, press the [MENU] button on the front panel and follow these steps: 1) To release the event monitoring mode: Set the duration of the event monitoring to Off in the Monitoring Mode settings. 2) To release the alarm sound: Deactivate the alarm sound in Event Record Mode - Alarm (Motion Detection/Video Loss). 3) To release the event: Set the mode to Off in Event Record Mode - Alarm (Motion Detection/ Video Loss).
How to fix Samsung SRD-470D DVR when the REC button doesn't work?
If the REC indicator doesn't flash and the player doesn't start recording when you press the [REC] button on your Samsung DVR, check if there's enough free space on the HDD. Also, verify that the record mode is set to ON in the record mode settings.
What to do if the 'NO HDD' icon appears on my Samsung SRD-470D?
If you see the “NO HDD” icon and an error message on your Samsung DVR, first check the physical connection of the HDD. If the problem continues under normal conditions, it's recommended to contact a service center to have the HDD inspected by qualified personnel.
What to do if the Samsung SRD-470D DVR does not turn on?
If your Samsung DVR isn't turning on, start by checking if the power supply is properly connected. Next, verify the system's input voltage from the power source. If it still fails to power on after these checks, the power supplier might be faulty and need replacement.
How to switch to Live mode on Samsung SRD-470D during playback?
General| Product color | Black |
|---|---|
| Channels quantity | 4 channels |
| Maximum recording time | 6 h |
| Video compression formats | H.264 |
| Operating system installed | Embedded LINUX |
| Analog signal format system | NTSC, PAL |
| Display resolution | 704 x 576 pixels |
| Video in | 4 |
| eSATA ports quantity | 0 |
| USB 2.0 ports quantity | 2 |
| Ethernet interface type | Fast Ethernet |
| Supported network protocols | TCP/IP, DHCP, PPPoE, SMTP, NTP, HTTP, DDNS, RTP, RTSP |
| HDD capacity | 500 GB |
| HDD interface | Serial ATA |
| Optical drive type | DVD-RW |
| Optical drive included | Yes |
| Operating temperature (T-T) | 0 - 40 °C |
| Operating relative humidity (H-H) | 20 - 85 % |
| Power requirements | 100 - 240V AC ±10%, 50/60Hz |
| Power consumption (typical) | 35 W |
Weight and Dimensions| Weight | 4000 g |
|---|---|
| Dimensions (WxDxH) | 215 x 352 x 88 mm |
Lists the key features of the SRD DVR.
Identifies and explains rear panel ports and connectors.
Identifies and explains front panel buttons and indicators.
Details the functions of the remote control buttons.
Guidelines for safe and proper installation of the DVR.
Instructions for installing additional Hard Disk Drives.
How to connect video, audio, and monitor equipment.
Instructions for connecting USB devices like HDDs and memory.
How to connect a POS device using the RS-232C port.
How to connect alarm input and output signals.
How to connect RS485 devices, like PTZ cameras.
Steps for connecting the DVR to a network.
Procedures for starting and shutting down the system.
How to log into the DVR for access and security.
How to enable and disable the button lock feature.
Understanding and configuring the icons on the live screen.
Information about common error messages and their causes.
Accessing menus via right-clicking on the live screen.
Context sensitive menus for split screen modes.
Context sensitive menus for single screen mode.
How to access and use the launcher menu.
Displaying live video images in different screen modes.
How to display channels in split screen and switch to single mode.
Monitoring a specific channel through the Spot Out port.
Enlarging a specific area of the live screen image.
Turning audio on or off for live channels.
Temporarily pausing the live video image.
Displaying channels synchronized with specific events.
Setting system properties like date, time, and language.
Configuring date, time, timezone, and language settings.
Setting specific dates as holidays for scheduling.
Setting user permissions and administrator access.
How to set the administrator's ID and password.
Using the on-screen virtual keyboard for input.
Creating user groups and setting their permissions.
Assigning menu permissions to group users per channel.
Limiting user access to default menus.
How users can change their own passwords.
Adding, editing, and configuring user accounts.
Setting restricted access for general users.
Checking system version, updating software, and backup.
Viewing system version, broadcast format, and MAC address.
Process for updating the DVR's software.
Copying and importing DVR settings using storage media.
Browsing system and event logs.
Viewing system startup, shutdown, and setting change logs.
Viewing recorded events on alarms, motion, and video loss.
Viewing details of backup operations.
Configuring device settings like camera, storage, and monitor.
Setting camera video, audio, name, and dwell time.
Configuring camera video, audio, channel name, and dwell time.
Configuring PTZ camera settings, ID, and protocols.
Checking and changing storage device settings.
Viewing storage devices, free space, usage, and status.
Formatting storage devices like HDDs or USB drives.
Setting alarm outputs and durations for HDD defects.
Setting RS-485 communication for PTZ cameras and keyboards.
Setting channel, preset, and communication ports for POS devices.
Configuring display information and format for Spot Out monitor.
Configuring displayed information and format for the Spot Out monitor.
Adjusting data position on the monitor when information is not displayed correctly.
Setting DVR to output information/video via the SPOT port.
Configuring live screen and playback screen modes.
Setting up scheduled, event, and other recording options.
Scheduling recordings for specific dates and times.
Explains color coding for recording modes.
Setting start and end times for event-activated recordings.
Setting resolution, IPS, and quality for recordings.
Setting resolution, quality, and IPS for normal recordings.
Setting resolution, frame rate, and quality for event recordings.
Setting disk end mode (stop or overwrite) and auto delete options.
Setting recording options for sensor, motion, and video loss events.
Configuring sensor operation, connected camera, and alarm settings.
Setting detection regions, sensitivity, and alarm output for motion.
Defining specific areas for motion detection.
Setting alarms for camera disconnections (video loss).
Scheduling alarm outputs based on day and time.
Setting the network connection route and protocol.
Configuring network protocol and environment settings.
Setting up DDNS for remote user network connection.
Details on connecting and setting the network based on router usage.
Setting static IP and DHCP for router connection.
Configuring router settings for DHCP.
Configuring port forwarding on the router.
Configuring DDNS settings in the DVR and router.
Setting image quality for network transferred images.
Configuring email notifications for events.
Setting up the SMTP server for sending emails.
Setting event types for email notifications.
Setting up email recipient groups and permissions.
Adding or removing email recipients.
Activating PTZ device functions.
Initial steps to start using PTZ camera control.
Operating PTZ camera functions like Pan, Tilt, and Zoom.
Setting and managing camera presets for PTZ control.
Optimizing PTZ camera settings via the DVR.
Accessing the search menu to find recorded data.
Searching recorded video data by specific time.
Searching for events by channel and playing them.
Searching for backup data in connected backup devices.
Searching for data from connected POS devices.
Searching for detected motion within specific areas.
Playing back stored data from HDD or backup.
Playing back stored data from HDD or backup.
Explains the functions of playback control buttons.
Overview of Web Viewer features and system requirements.
Steps to connect to the DVR using the Web Viewer.
Navigating and using the live viewer interface.
Understanding the on-screen display information in Live Viewer.
Changing the split mode for viewing multiple cameras.
Displays IP address and status of the connected DVR.
Configuring OSD time display settings.
Switching live screen modes like Sequence, Previous, Next.
Capturing, printing, and recording live screens to PC.
Changing the displayed live screen channel.
Controlling PTZ cameras via the web viewer.
Interface for searching recorded video via the web viewer.
Changing split modes in the search viewer.
Displaying connected DVR IP and status in search viewer.
Searching recorded video using a calendar interface.
Searching recorded video using a timeline interface.
Controlling playback of recorded video.
Configuring DVR settings remotely via network.
Configuring various DVR system settings.
Setting date, time, language, and holidays.
Setting specific dates as holidays for scheduling.
Managing user access and permissions.
Checking system information and managing software.
Checking and configuring connected devices like cameras and storage.
Configuring camera settings.
Configuring PTZ camera settings, ID, and protocol.
Checking and changing storage device settings.
Setting alarm outputs for HDD errors.
Configuring remote devices like PTZ cameras.
Setting up POS devices connected to the DVR.
Configuring monitoring screen settings.
Selecting video output mode for external monitoring on events.
Switching between live and playback modes.
Setting recording schedules and options.
Setting specific recording schedules for dates and times.
Setting start and end times for event-activated recordings.
Setting resolution, frame rate, and quality for recordings.
Setting disk end mode and auto delete options.
Configuring event recording options.
Setting sensor operation, camera, and alarm settings.
Setting motion detection modes and regions.
Setting alarms for video loss.
Scheduling alarm outputs based on day and time.
Configuring network settings.
Setting the network connection route.
Configuring protocol-related network settings.
Checking and configuring DDNS settings.
Setting image quality for network transferred images.
Configuring email notifications for events.
Setting up the SMTP server for sending emails.
Setting event types for email notifications.
Setting up email recipient groups and permissions.
Adding users who will receive emails.
Information about the mobile viewer application.
Playing back backup files in SEC format.
System requirements for backup viewer.
Explains the functions of the backup viewer's playback controls.
Detailed technical specifications for SRD-470 and SRD-470D.
Visual overview of the DVR hardware dimensions.
Lists the factory default settings for various parameters.
Provides common issues and their solutions.
To Next Page
