Sanyo PLC-XR201 User Manual

-43-
Electrical Adjustments
Group/
Item
Item Name Function Initial Range Note
231 Output limit B
2686/3274
0-4095
232 CROSSTALK_COEF_R
1023
0-1023
233 CROSSTALK COEF_G
1023
0-1023
234 CROSSTALK COEF_B
1023
0-1023
235 LCCON_ENABLE
0
0-1
236 ENBY_L1
10
0-255
237 ENBY_H1
674
0-1023
238 ENBY_L2
10
0-255
239 ENBY_H2
674
0-1023
Group
101
Panel Service(6170/62334)
0 R_LCCOM 160 0-255
1 G_LCCOM 160 0255
2 B-LCCOM 160 0-255
3 R-ENBX-PW 5 0-15
4 G-ENBX-PW 5 0-15
5 B-ENBX-PW 5 0-15
6 R-DXIN 48 0-127
7 G-DXIN 48 0-127
8 B-DXIN 48 0-127
9 R-ENB11N 16 0-31
10 G-ENBX11N 16 0-31
11 B-ENBX11N 16 0-31
12 Vmid - 0-255
13 R-Ref - 0-255
14 G-Ref - 0-255
15 G-Ref - 0-255
16 Vref 190
Group
102
Auto Keystone Setup Value
0 OFFSET 0
-1056 -
1056
1 OFFSET SWITCH
0
0 - 1
2 DEBUG MODE
0
0 - 1
3 SERVICE CALIBRATION
0
0 - 1
4 LOCK COUNT
5
1 - 255
5 DELT VERT RESULT
64
1 - 255
6 ANGLE 1 COUNT
1
1 - 10
7 ANGLE 2 COUNT
5
1 - 10
8 BLIND SECTOR 1
160
0 - 1024
9 BLIND SECTOR 3
32
0 - 1024
10 BLIND SECTOR BIAS
61
0 - 1024
Group
200
Option
0 Logo Prohibition Logo Prohibition (0: Menu, 1: Forced) 0 0 - 1 Effective after AC On
1 RS232C Baudrate Baud Rate 0 0 - 2
0: 19200bps, 1: 9600bps, 2:
115200bps
2 PJLink Enable PJLink 0 0 - 1 0: Disable 1: Enable
4 CABLE SW Long Cable 0 0 - 10 0: Disable, 1: Enable
5
PW Debug Command
Enable
0 0 - 1
0:Disable (Serial Command Eanble)
1: Enable (PW Debug Mode)
6 Device Refresh Disable 0 0 - 1
0:Enable, 1:Disable
No last memory
7 Device Access Disable 0 0 - 1
0:Enable (Normal), 1:Disable
No last memory
21
Lamp Warning Time
(NORMAL)
Lamp Life at Normal Mode (Warning
Time at Normal)
- 500-8000
22 Lamp Warning Time (ECO)
Lamp Life at Eco Mode (Warning
Time at Eco)
- 500-8000
23 Lamp Warning Time (HIGH)
Lamp Life at High Mode (Warning
Time at High)
- 500-8000
40
Lamp PWM PresAv
50Hz
80 0-255
41
Lamp PWM PresAv
60Hz
67 0-255

Sanyo PLC-XR201 Specifications

General

Brand	Sanyo
Model	PLC-XR201
Category	Projector
Language	English