Sanyo PLC-XU75 Service Manual

-45-
Group/
Item
ITEM NAME FUNCTION INITIAL RANGE NOTE
5 Image AREA V HIGHT Black/White Level Acquiring Area Height 9 0 - 4095
6 OFFSET target Target Value of Black Level Adj. 3 0 - 127
7 OFFSET torelance Torelance of Black Level Adj. 1 1 - 127
8 GAIN target Target Value of White Level Adj. 238 0 - 255
9 GAIN torelance Torelance of White Level Adj. 1 1 - 255
Group 262 Auto Calibration (CVBS/SVIDEO)
0 Y Image Area Start X Y Acquiring Area H-Start Position 20 0 - 1000
1 Y Image Area Start Y Y Acquiring Area V-Start Position 500 0 - 1000
6 Image Area H Width Image Level Acquiring Area 13 0 - 4095
7 Image Area V Hight Image Level Acquiring Area Height 20 0 - 4095
8 Y Target Level Target Value of Y Level Adj. 217 0 - 255
11 Gain Tolerance Torelance of Level Adj. 1 0 - 255
12 Delta Gain Deviation Width of Gain Value 9 0 - 255
Group 264 Auto Calibration (YCbCr)
0 Y-OFFSET AREA H START Y - Offset Acquiring Area H-Start Position 925 0 - 1000
1 Y-OFFSET AREA V START Y - Offset Acquiring Area V-Start Position 500 0 - 1000
2 CB - OFFSET AREA H START CB - Offset Acquiring Area H-Start Position 925 0 - 1000 If not used: use Y's value
3 CB - OFFSET AREA V START CB - Offset Acquiring Area V-Start Position 500 0 - 1000 If not used: use Y's value
4 CR - OFFSET AREA H START CR - Offset Acquiring Area H-Start Position 925 0 - 1000 If not used: use Y's value
5 CR - OFFSET AREA V START CR - Offset Acquiring Area V-Start Position 500 0 - 1000 If not used: use Y's value
6 Y - GAIN AREA H START Y 50 0 - 1000
7 Y - GAIN AREA V START 500 0 - 1000
8 CB - GAIN AREA H START 800 0 - 1000
9 CB - GAIN AREA V START 500 0 - 1000
10 CR - GAIN AREA H START 700 0 - 1000
11 CR - GAIN AREA V START 500 0 - 1000
12 Image AREA H WIDTH YCBCR Level Acquiring Area 8 0 - 4095
13 Image AREA V HIGHT YCBCR Level Acquiring Area Height 9 0 - 4095
14 Y - OFFSET TARTGET 4 0 - 255
15 CB OFFSET TARGET 128 0 - 255
16 CR OFFSET TARGET 128 0 - 255
17 Y - GAIN TARGET 217 0 - 255
18 CB - GAIN TARGET 237 0 - 255
19 CR - GAIN TARGET 237 0 - 255
20 OFFSET torelance Torelance of OFFSET Adj. 1 1 - 255
21 GAIN torelance Torelance of GAIN Adj. 1 1 - 255
Group 270 Custom (Aspect)
0 Scaler Horizontal H-Scaler 100 68-132
1 Scaler Vertical V-Scaler 100 68-132
2 Connect Link Edit 1: Link 0 0-1
3 Position Horizontal H-Position 100 85-115
4 Position Vertical V-Position 100 85-115
5 Aspect Enable Aspect Enable (0: On, 1: Off) 0 0-1
Group 280 AutoPC Adjsut
0 AutoPCAdjustEnable
Auto-PC Adj Operation Enable if Un-
supported Signal Input
0 0 - 1 0: Enable, 1: Disable
1 Frequency Step Frequency Steps of TotalDot 1 0-3
2 Frequency Threshold Total Dot Freqency Threshold 5 0 - 10 0 [] <--- -----> 10[Not matched]
3 Fine Phase Do Phase Adj after Total Dot Adj. 1 0 - 1 0: Executes Fine Phase, 1: Not Execute
4 BLKDET Black Level Detection Area 1 0 - 3
5 PHASEMSK Phase Detection Filter 0 0 - 3
0: Effective All Bit,
1: Disable Lower 1 bit
2: Disable Lower 2 bit, 3: Disable Lower 3 bit
Group 290 PanelType * Panel Type Check
0 GammaL/R-View Current Setting Check 0 0-20
0: Gamma for L-Turn
20: Gamma for R-Turn * Read only
1 GammaL/R-Change Setting of Gamma 10 0-20
Sets L-Turn Gamma if the Value is set to 0.
Sets R-Turn Gamma if the Value is set to 20.
Group 500 Composite (NTSC) Composite / S-Video
0 * Read only
1 Disp Dots 668 0 ~ 4095
2 H Back Porch 28 0 ~ 4095
3 V Back Porch 18 0 ~ 4095
4 Disp Line 458 0 ~ 4095

Sanyo PLC-XU75 Specifications

General

Brand	Sanyo
Model	PLC-XU75
Category	Projector
Language	English