102
“Classification” Application
The initialization block contains the
upper limits of weight classes 1, 2, 3, 4.
The results block contains gross,
net and tare weights, as well as the
assigned weight class as a result
(1 to 5, whereby class 5 is the one
that exceeds class 4).
HEADER LINE1
HEADER LINE2
14.07.2010 09:43
--------------------
Lim1 + 10.000 kg
Lim2 + 11.000 kg
Lim3 + 12.000 kg
Lim4 + 13.000 kg
G# + 9.700 kg
T + 0.000 kg
N + 9.700 kg
Class 1
1
)
--------------------
1
) Classification can range from 1 to 5.
The sample is assigned to class 5 if its
weight exceeds the weight limit “Lim4"
and “5 classes" was previously selected
in the menu.
“Animal Weighing” Application
The Initialization data block contains
the number of measured values that
averaging is based on. The results
block contains the tare weight and
the average value.
HEADER LINE1
HEADER LINE2
14.07.2010 09:43
--------------------
mDef 8
T + 0.000 kg
x-Net + 4.202 kg
--------------------
“Net-total Formulation” Application
The Initialization data block is empty.
The data that is contained in the
results block depends on the program
operating status at the time of
printing. The following options are
available:
– Total/results printout (c key)
– Individual/components printout (when
the “
M+" soft key is pressed to save a
component, or when p is pressed for
an individual printout)
Total printout
HEADER LINE1
HEADER LINE2
14.07.2010 09:43
--------------------
n 3
Tot.cp+ 3.400 kg
Cont.T+ 0.200 kg
--------------------
Individual/Component Printout
If you press O the header is printed
only once. Each component is printed
automatically when you press
M+.
If this printout should be printed on a
label printer, the label length should be
checked. For printer models YDP01IS
and YDP04IS, you can configure
manual form feed in the Setup menu.
With the YDP02IS printer, form feed is
automatic after each print command
(fixed setting).
If an automatic printout is generated
when you store a component, the
component weight is equal to the
current net weight. This is why
components rather than net weights
are printed.
Menu setting “Print components" with
3 components:
HEADER LINE1
HEADER LINE2
14.07.2010 09:43
--------------------
Cmp001+ 1.200 kg
Cmp002+ 2.000 kg
Printout of third component generated
by pressing p.
G# + 4.400 kg
T + 0.200 kg
T2 + 4.200 kg
N + 0.000 kg
Individual printout when storing a
component in tare memory by pressing
O.
Menu setting “Print components"
example: print 2nd component
HEADER LINE1
HEADER LINE2
14.07.2010 09:43
--------------------
Cmp002+ 1.000 kg
Individual printout of component
generated by pressing p, example:
2nd component
HEADER LINE1
HEADER LINE2
14.07.2010 09:43
--------------------
G# + 2.400 kg
T + 0.200 kg
T2 + 2.200 kg
N + 0.000 kg
“Totalizing” application
The initialization data block is empty;
an empty line is printed as required.
The values displayed in the results
block depend on the program status.
The following options are available in
the Setup menu:
– Results printout (press c key):
Printout of values from gross totalizing
memory “*G,” net totalizing memory
“*N” and number of transactions “n”.
– Individual/component printout
automatic with
M+ soft key
– Individual/component printout manual
with p key
The record header is only printed once
for the component printout.
All components are printed one below
the other.
If this printout should be printed on a
label printer, the label length should be
checked (see “Net Total" application).
The transaction counter is not printed
for a manual printout (with the p
key).
Data Interfaces
To Next Page
Loading...
Need help?
General
