SATO CL4NX Plus Installation Manual

First edition: Feb. 2020 Q05346500
©2020 SATO Corporation
Rotary Cutter Kit
Installation Manual
Accessories
This Installation Manual explains how to install Rotary Cutter Kit (hereafter referred to as
“the product”). Read the restrictions and precautions when installing.
For details on how to use Rotary Cutter Kit and how to use and operate CL4NX Plus setting
items, see CL4NX Plus web manual “Operator Manual”.
 






Cutter unit

Bracket

Cutter cable

Cover

Relay PCB

Installation Manual (this document)

Screws
Screws for xing the Relay PCB (2 pcs)
Screws for xing the bracket (3 pcs)
Screws for xing the cutter unit (2 pcs)
Black screws for xing the cover (2 pcs)
Required tool
• Phillips screwdriver (JIS #2 or equivalent)
Installing the Cutter Unit
1
Make sure that the CL4NX Plus is powered off and disconnect the
power cord from the AC outlet.
2
Open the top cover and push the
head lock lever towards the rear
to unlock the print head.
Tip
Open the top cover fully to prevent
accidental drop of the cover.

Website
http://www.satoworldwide.com/
Safety Precautions
This section describes how to use the product safely. Be sure to read the following information
carefully before using the product.
Pictographic Symbols
This installation manual uses a variety of pictographic symbols. These symbols emphasize the
safe and correct use of the product and to prevent injury to others and property damage. The
explanation of the symbols is as follows. Be sure to understand these symbols well before you
read the main text.
WARNING
Ignoring the instructions marked by this symbol and erroneously
operating the product could result in death or serious injury.
CAUTION
Ignoring the instructions marked by this symbol and erroneously
operating the product could result in injury or property damage.
Symbol example
The pictograph means “Caution is required”. A specic warning symbol is
contained inside this pictograph.
The pictograph means “Should not be done”. What is specically prohibited is
contained in or near the pictograph.
The pictograph means “Must be done”. What is specically to be done is
contained in the pictograph.
WARNING
Do not place in high-temperature locations
Do not place the product near heating equipment such as cooking appliances or
a heater, or in high-temperature locations. Doing so could damage the product or
result in a re or electric shock.
Connecting cables or optional devices
• When connecting a cable or optional device to the product, be sure to turn off
each of the devices. If they are connected with the power on, an optional device
could move unexpectedly, resulting in injury, electric shock, or damage.
• When installing a cable or optional device, be sure not to make a mistake in the
orientation and steps to install. Otherwise, it could result in injury, re, electric
shock, or damage.
• Do not use cables other than the ones supplied with the product or recommended
by us. Doing so could result in smoke, re, electric shock, or damage.
WARNING
Do not operate with wet hands
Do not power on/power off the product or plug/unplug the power cord and other
cables with wet hands. Doing so could result in electric shock or damage.
Do not touch or insert any object in the cutter
Do not touch the cutter with your hands or insert foreign objects other than media
into the cutter. Doing so could result in injury.
CAUTION
Power cord and other cables
• Grab a power cord and other cables by the plug when removing from the outlet
or connector port. Removing a power cord and other cables by grabbing the
cord/cable area could result in exposure of wires, breakage, re, electric shock,
or damage.
• Do not place the power cord and other cables near a heater or other sources
of heat. Doing so could result in melting of the power cord and other cables
sheathing, re, electric shock, or damage.
Handling
Some parts of the product are sharp. Be careful not to get injured.
Precautions on Installation and Handling
• For details on the restrictions and precautions on installation of CL4NX Plus, see the CL4NX
Plus web manual “Operator Manual”.
• The product works with 1.12.0 version rmware build or later. Check the rmware version
shown on the [Information] Menu > [Build Version] screen of CL4NX Plus. Contact your
SATO reseller or technical support for availability of the latest rmware.

SATO CL4NX Plus Specifications

General

Display type	LCD
Product color	Black
Built-in display	Yes
Display diagonal	3.5 \
Type	POS printer
Color	No
Print speed	14 ips
Print technology	Direct thermal / Thermal transfer
Maximum resolution	305 x 305 DPI
AC input voltage	100 - 240 V
Power source type	AC
AC input frequency	50 - 60 Hz
Maximum media length	600 mm
Maximum roll diameter	254 mm
Supported paper width	39.5 - 128 mm
Maximum printing width	128 mm
Printing media thickness	0.06 - 0.268 µm
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	30 - 90 %
Operating relative humidity (H-H)	30 - 80 %
Wi-Fi	-
USB connector	USB Type-A / USB Type-B
Bluetooth version	3.0+HS
Standard interfaces	Bluetooth, Ethernet, RS-232C, Serial, USB 2.0
Serial interface type	RS-232C
USB 2.0 ports quantity	3
Connectivity technology	Wired & Wireless
Ethernet LAN (RJ-45) ports	1

Weight and Dimensions

Depth	271 mm
Width	457 mm
Height	321 mm
Weight	15100 g