Need help?Do you have a question about the SATO CT4-LX and is the answer not in the manual?
General| Print Method | Thermal Transfer / Direct Thermal |
|---|---|
| Print Resolution | 203 dpi |
| Max Print Width | 4.09 inches (104 mm) |
| Media Type | Roll, Fan-fold |
| Media Thickness | 0.0025 to 0.008 inches (0.0635 to 0.2032 mm) |
| Ribbon Width | 0.98 inches (25 mm) to 4.09 inches (104 mm) |
| Ribbon Length | 984 feet |
| Connectivity | USB, Ethernet, Bluetooth |
| Supported Barcode Types | PDF417, QR Code |
| Power Requirements | 100-240 VAC, 50/60 Hz |
Describes how to use the product safely and outlines pictographic symbols.
Instructions on how to install and handle the product safely.
Explains how to handle errors, including clearing and using SOS.
Guide to adjust print position, darkness, and speed during printing.
Step-by-step instructions to enter the Settings mode.
Explains the procedure for logging in and out of the Settings mode.
Instructions for connecting the AC adapter and power cord safely.
Steps to power on the product and details on startup guide appearance.
Procedure for safely powering off the product.
Outlines steps for connecting interfaces, configuring settings, and installing drivers.
Instructions for downloading and installing the printer driver.
Explains the Label Waste Prevention function for aligning labels.
Details on adjusting label top sensor position and sensitivity.
Explains how media sensors detect I-marks or Gaps for print position.
Explains conditions that trigger a paper end error during feeding.
Details settings in the [Printing] menu: Media Type, Label Length, Label Width.
Sets the sensor type for detecting media (None, Gap, I-Mark).
Adjusting media sensor level and auto-calibration options.
Settings for LAN interface, including IP address assignment methods.
Details RFID write operation in continuous mode with tag offset zero.
Details RFID write in continuous mode with tag offset greater than zero.
Details RFID write operation in tear-off mode with tag offset zero.
Details RFID write in tear-off mode with tag offset greater than zero.
Details RFID write in cutter mode with backfeed after printing.
Details RFID write in cutter mode with backfeed after printing and offset > 0.
Details RFID write in cutter mode with backfeed before printing.
Details RFID write in cutter mode with backfeed before printing and offset > 0.
Explains RFID write in cut & print mode, including offset and error print.
Steps to adjust the print position using the Pitch setting.
Steps to adjust the media stop position using the Offset setting.
Steps to adjust the label top sensor position for print start alignment.
Procedure to adjust the print darkness via the Settings menu.
Procedure to adjust print speed, affecting speed and quality.
Use RF Analyze to measure RFID tags and set consistent write/read conditions.
Explains how product prints RFID tag errors on defective media.
Enables auto-clone function to save settings to USB memory automatically.
Explains cause and countermeasure for a machine error.
Explains cause and countermeasure for a program error.
Explains cause and countermeasure for a parity error.
Explains cause and countermeasure for an overrun error.
Explains cause and countermeasure for a framing error.
Explains cause and countermeasure for a buffer overflow error.
Explains cause and countermeasure for a cover open error.
Explains cause and countermeasure for an out of paper error.
Explains cause and countermeasure for a ribbon end error.
Explains cause and countermeasure for a media error.
Explains cause and countermeasure for a print head error.
Explains cause and countermeasure for USB read/write errors.
Explains cause and countermeasure for USB memory full error.
Explains cause and countermeasure for a cutter error.
Explains cause and countermeasure for an SBPL command error.
Explains cause and countermeasure for RFID system errors.
Explains cause and countermeasure for a calendar error.
Explains cause and countermeasure for a BCC check error.
Explains cause and countermeasure for print head overheating.
Explains cause and countermeasure for NTP connection errors.
Explains cause and countermeasure for print head density change.
Explains cause and countermeasure for a gap not found error.
Explains cause and countermeasure for an I-mark not found error.
Explains cause and countermeasure for EAP authentication failure.
Explains cause and countermeasure for EAP authentication timeout.
Explains cause and countermeasure for Bluetooth module errors.
Explains cause and countermeasure for CRC check errors.
Explains cause and countermeasure for a paper jam.
Explains cause and countermeasure for a WLAN module error.
Explains cause and countermeasure for RFID undetected warnings.
Explains cause and countermeasure for NFC module errors.
Explains cause and countermeasure for invalid NFC commands.
Explains cause and countermeasure for configuration warnings.
Explains cause and countermeasure for Label Waste Prevention errors.
Explains cause and countermeasure for RFID tag not found errors.
Explains cause and countermeasure for RFID write operation failures.
Explains cause and countermeasure for failing to read tag data.
Explains cause and countermeasure for inconsistent RFID write/read values.
Explains cause and countermeasure for failing to lock RFID data.
Explains cause and countermeasure for detecting multiple RFID tags.
Explains cause and countermeasure for EPC mismatch in RFID tags.
Explains cause and countermeasure for write-lock or low power RFID errors.
Explains cause and countermeasure for insufficient RFID power.
Explains cause and countermeasure for auto-clone errors.
Explains cause and countermeasure for Bluetooth MFi chip module errors.
Explains cause and countermeasure for RTC module errors.
Explains cause and countermeasure for SRA motor unit errors.
Explains cause and countermeasure for RFID module overheating.
To Next Page
