Scheppach HM140L User Manual

www.scheppach.com
30
|
GB
Weight 20,8 kg
Laser class 2
Wavelength of laser 650 nm
Laser output ≤ 1 mW
* S6, continuous operation periodic duty.
Identical duty cycles with a period at load fol-
lowed by a period at no load. Running time 5
minutes; duty cycle is 40% of the running time.
The work piece must have a minimum height of
3 mm and a minimum width of 10 mm. Make sure
that the workpiece is always secured with the
clamping device.
Noise and vibration
Total vibration values determined in accordance with
EN 62841.
Sound pressure level L
pA
95 dB(A)
Uncertainty K
pA
3 dB
Sound power level L
WA
108 dB(A)
Uncertainty K
WA
3 dB
Wear hearing protection.
The e󰀨ects of noise can cause a loss of hearing. Total
vibration values (vector sum - three directions) deter-
mined in accordance with EN 62841.
Residual risks
The machine has been built according to the state
of the art and the recognised technical safety re-
quirements. However, individual residual risks can
arise during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been met,
some non-obvious residual risks may still remain.
• Residual risks can be minimised if the „safety in-
structions“ and the „Proper use“ are observed along
with the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the ma-
chine in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be xed between the clamps.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with un-
protected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specied here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure
to the beam can occur.
• If the mitre saw is not used for an extended period
of time, the batteries should be removed.
• The laser may not be replaced with a di󰀨erent type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.
6. Technical data
AC motor 220 - 240 V~ 50Hz
Power
2000 Watt / S6 40%*
1800 Watt / S1
Idle speed n
0
3800 min
-1
Carbide saw blade
ø 305 x ø 30 x 3/2,8
mm
Number of teeth 24/48
Swivel range -45° / 0°/ +45°
Mitre cut 0° bis 45° to the left
Saw width at 90° 330 x 105 mm
Saw width at 45° 230 x 60 mm
Saw width at 2 x 45° right
(double mitre cut)
230 x 35 mm
Saw width at 2 x 45° left
(double mitre cut)
230 x 60 mm
Protection class II

Scheppach HM140L Specifications

General

Input power	2000 W
Power source	AC
AC input voltage	230 - 240 V
AC input frequency	50 Hz
Saw blade included	Yes
Number of blade teeth	48
Idle speed (max)	7000 RPM
Bevel type	Double bevel

Weight and Dimensions

Depth	750 mm
Width	590 mm
Height	500 mm
Weight	21030 g
Package weight	25660 g