www.scheppach.com
24
|
GB
Installation of the castors (12) (Fig. 3)
1. Press the two deection rollers (12) into the holes
provided in the roller mounts (12a).
Installing the machine head with lter cage (3)
(Fig. 8)
1. Place the machine head with lter cage (3) on the
stainless steel container (1).
2. Secure the machine head (3) with the locking
hooks (8). When installing the machine head with
lter cage (3), ensure that the locking hooks (8)
latch into place correctly. The water channel con-
nection (4) must be above the vacuum connection
(2).
Installing the lter (33) (Fig. 5, 6)
Never use the device without lter! Always ensure that
the lters are correctly tted.
Installing the foam lter (33)
1. For wet vacuuming, open and remove the lter
cage (3a) by turning it anti-clockwise (Fig. 6).
2. Pull o the clipped cover cap (3b) with a screw-
driver (not included in the scope of delivery), pull
the foam lter (33) over the lter cage with safety
oat valve (3c) and ret the cover cap (3b) (Fig. 5).
3. Now reinsert the lter cage by turning it clockwise
(Fig. 6).
To avoid tearing the foam lter (33),
• only insert a dry lter
• knock the edge of the lter over a little to insert it and
then roll it back again.
Fit the folded lter (31) and foam lter (32) (not in-
cluded in the scope of delivery)
1. Open and remove the lter cage (3a) by turning it
anti-clockwise (Fig. 6).
2. Insert the hepa lter (31) or foam lter (32) and re-
place the lter cage by turning it clockwise (Fig. 6).
Installing the paper lter bag (34) (g. 7)
It is recommended to use an additional paper lter bag
(34) when vacuuming ne, dry dirt.
1. Slide the paper lter bag (34) over the suction
opening in the stainless steel container (1).
The paper lter bag (34) is only suitable for dry
vacuuming. The paper lter bag (34) makes it eas-
ier to dispose of the dust collected.
8. Unpacking
• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating instructions before using for the rst time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Replace-
ment parts can be obtained from your dealer.
• When ordering please provide our article number as
well as type and year of manufacture for your equip-
ment.
m WARNING!
The device and the packaging material are not
children’s toys! Do not let children play with plas-
tic bags, lms or small parts! There is a danger of
choking or suocating!
9. Assembly / Before commissioning
m ATTENTION!
Prior to use, ensure that the device has been correct-
ly and fully assembled.
Unpacking (Fig. 1, 2)
• Release the locking hooks (8) and remove the ma-
chine head with lter cage (3). The accessories are
located inside the stainless steel container (1). Only
the extension pipes (25) are located outside the
stainless steel container (1) in the packaging. Re-
move all of the accessories from the stainless steel
container (1).
Installation of the roller mounts (11 + 12) (Fig. 3)
1. Turn the stainless steel container (1) upside down.
(The machine head with lter cage (3) must be re-
moved.)
2. Slide the wheels (11) into the recesses provided on
the caster mounting base (13) and screw them in
place with the screws (30).
To Next Page
Loading...
