Scheppach SprayVac20 - Fill Water Tank; Install Water Tank; Connect Suction Hose; Vacuuming Operation Setup

www.scheppach.com
GB
|
25
Fitting the water channels (16, 24, 25) (g. 12, 13)
1. To do this, push the end of the respective water
channel (16, 24) with the two nipples into the water
channel connection (4, 7).
2. Insert the two nipples into the recesses. In the end
position, turn the water channel (16, 24) in a clock-
wise direction. (Fig. 12, 13).
3. Slide the end of the water channel from the end
of the plastic tube (25) or the curved end of the
suction pipe (21) with the two nipples into the re-
cesses at one of the corresponding nozzles (26,
27, 28, 29).
4. In the end position, turn the water channel in a
clockwise direction. (Fig. 13).
10. Start up
Warning! Switch the device o󰀨 if liquid or foam
emerges with the exhaust air during wet vacuum-
ing.
Switching on/o󰀨 (g. 11)
1. Connect the mains plug of the device.
2. Press the on/o󰀨 switch (5):
• Switch setting 0: O󰀨
• Switch setting I: On
• Switch setting II: On + spray function
Switching on the washing function (Fig. 19)
1. Switch on the device with the spray function (see
Switching on/o󰀨)
2. Press the pump switch (19)
Air regulation (Fig. 19)
The device has an air control (20a) with which the suc-
tion capacity can be adjusted.
1. To do this, move the air regulation switch (20a) on
the handle (20) until the desired air regulation is
reached.
Wet vacuuming
• Use the foam lter (33) for wet vacuuming.
• Ensure that the foam lter (33) is correctly tted.
• If the stainless steel container (1) is full, the safety
oat valve (3c) closes the suction port and suction
operation is interrupted.
m Attention!
The device is not suitable for vacuuming ammable
liquids. For wet vacuuming, use the only the foam lter
(3) provided
Filling the water tank (Fig. 15)
The water tank (9) can be removed for lling or lled
directly at the device.
1. Fill the water tank (9) through the opening (17) with
clear water (max. 3 l). Pay attention to the mark-
ings on the container (10)
2. If the water tank is heavily contaminated or
stained, add a little cleaning agent, e.g. carpet and
upholstery cleaner.
Installing the water tank (Fig. 4)
1. Take the water tank (9) by the handle (18) and
place it in the openings of the caster mounting
base (13).
2. Now press the water tank (9) against the detent
(1a) until it locks into place.
Installing the suction hose (Fig. 10)
1. Connect the suction hose (22) to the correspond-
ing port, depending on the desired use, on the wet
and dry vacuum cleaner.
Vacuuming (Fig. 10)
1. Connect the suction hose (22) to the suction hose
connection (2).
2. To do so, slide the end of the suction hose (23)
with the two nipples into the suction hose port (2).
3. Insert the two nipples into the recesses. In the end
position, turn the suction hose (22) in a clockwise
direction.
Blowing (Fig. 11)
1. Connect the suction hose (22) to the blast function
connection port (14a).
2. Slide the end of the suction hose (23) with the
two nipples into the blast function connection port
(14a).
3. Insert the two nipples into the recesses. In the end
position, turn the suction hose (22) in a clockwise
direction.
Fitting plastic extension tubes (25), suction hose
(22) and nozzles (26, 27, 28, 29, 36)
(Fig. 10, 13)
1. Connect the plastic extension tubes (25) together.
2. Connect the assembled plastic extension tubes
with the bent end of the suction hose (21).
3. Fit one of the corresponding nozzles (26, 27, 28,
29, 36) to the end of the plastic tube (25) or the
curved end of the suction pipe (21).