What to do if I forgot my Schlage door lock programming code?
Check the back of this guide or the back of the Alarm Assembly for the default Programming Code. If needed, you can restore the lock to factory settings.
Why can't I add a new user code to my Schlage door lock?
There are several possible reasons: You may not have pressed '1' after entering Programming Mode; 30 User Codes may already exist (delete a User Code before adding a new one); The second User Code entry did not match the first; or the new User Code matches the first 4-6 digits of the existing Programming Code.
What to do if the Schlage door lock yellow dot is flashing?
The battery is low and should be replaced.
Why can't I delete a user code on my Schlage door lock?
Possible reasons include: '2' was not pressed after entering Programming Mode; the first User Code entered did not match any current User Code; or the second User Code entered did not match the first User Code entered.
Why is the Schlage door lock backlighting not working?
This could be due to completely dead batteries, a disconnected battery tray, or a disconnected cable running through the door.
Why can't I change the programming code on my Schlage door lock?
Possible causes: '3' was not pressed after entering Programming Mode; the second Programming Code entered did not match the first; or the first 4-6 digits of the new Programming Code match an existing User Code.
Why does my Schlage door lock show 3 red lights?
The battery is critical and must be replaced.
Why can't I delete all user codes on my Schlage door lock?
This may be because '6' was not pressed after entering Programming Mode, or the 2nd Programming Code entered was not valid.
Why is my Schlage door lock bolt not operating smoothly?
The bolt may have become soiled; clean it with mild detergent and warm water. Alternatively, the strike may have become worn; flip the strike over for continued smooth operation.
What to do if my Schlage door lock alarm sounds too frequently?
The sensitivity level might be too high (at 1 or 2) or too low (at 4 or 5). Adjust the sensitivity level.
Set the length of user codes (4-8 digits) before adding them.
Add or remove user codes from the lock, including presets.
Configure automatic relocking after the door is unlocked.
Turn on the alarm and select its operating mode.
Button on the interior side of the lock for programming.
Used for manual locking/unlocking from the interior.
Primary button on the exterior for interaction and programming.
Interface for entering codes on the exterior.
Key cylinder for emergency key override.
The deadbolt mechanism of the lock.
Emits sounds for alarm and feedback.
How to lock the deadbolt from the exterior.
How to lock the deadbolt from the interior.
How to unlock the deadbolt using a code.
How to unlock the deadbolt manually from the interior.
Advice and resources for effective programming.
Add new user codes to the lock.
Remove a specific user code.
Update the master programming code.
Temporarily disable all user codes.
Re-enable user codes after vacation.
Control audible feedback from the lock.
Remove all programmed user codes.
Configure auto-locking behavior.
Set the digit length for user codes.
Enable automatic relocking.
Manual override for auto-lock.
Revert to the default auto-lock setting.
Instructions for programming without a network.
Steps to turn the alarm function on.
Details on different alarm modes and triggers.
Select between Activity, Tamper, or Forced Entry modes.
Fine-tune the alarm's sensitivity.
Information on creating and using user codes.
Recommendations for secure code management.
Where to find initial programming and user codes.
Reasons for resetting the lock to defaults.
Step-by-step procedure for resetting.
Overview of Z-Wave technology and its use.
Guide to connecting the lock to a Z-Wave network.
General| Lock Type | Deadbolt |
|---|---|
| Keyless Entry | Yes |
| Connectivity | Z-Wave |
| Battery Type | 4 AA batteries |
| Touchscreen | Yes |
| Compatibility | Z-Wave |
| Product Type | Electronic Deadbolt |
| Power Source | Battery |
| User Codes | Up to 30 |
| Keypad | Yes |
| Bump Proof | Yes |
| Keyway | Schlage C Keyway |
| Programmable Codes | Yes |
| Weather Resistance | Yes |
| Security | ANSI Grade 1 |
| Finish Options | Bright Brass, Satin Nickel |
| Finish | Satin Nickel |
| Backset | 2-3/8" or 2-3/4" |
| Operation | Motorized bolt |
| Alarm Technology | Yes, built-in alarm |
To Next Page
