C
Carol StoutAug 20, 2025
Why doesn't my Schlage ALLEGION BE469 Door locks User Code unlock the lock?
- TthodgesAug 20, 2025
If your Schlage door lock's user code isn't unlocking the lock, the user code you entered is not a valid user code.
To Next PageTo Next PageWhy doesn't my Schlage ALLEGION BE469 Door locks User Code unlock the lock?
If your Schlage door lock's user code isn't unlocking the lock, the user code you entered is not a valid user code.
What to do if Deadbolt will not extend or retract on Schlage Door locks?
If your Schlage door lock's deadbolt is not extending or retracting as expected, adjust the bolt and frame alignment.
Why is the Schlage ALLEGION BE469 Door locks backlighting not working and I can't enter the User Code?
If the backlighting doesn't activate and you can't enter your user code after pressing the outside Schlage button on your Schlage door lock, there are several potential causes: * The batteries may be completely dead, preventing any electronic operations. If this is the case, replace the batteries. * The battery tray might not be connected properly. * The cable running through the door could be disconnected. To check this, remove the alarm assembly and inspect the connection.
How to find forgotten Programming Code for Schlage ALLEGION BE469 Door locks?
If you've forgotten your programming code for your Schlage door lock, check the back of the guide or the back of the alarm assembly for the default programming code. If necessary, you can restore the lock to its factory settings.
How to delete a User Code that I don’t remember on Schlage Door locks?
To delete a user code you don't remember on your Schlage door lock, delete all user codes and then re-add the ones you need.
What does 3 Red mean on Schlage Door locks?
If your Schlage door lock is displaying three red indicators when the outside Schlage button is pressed, the battery is critically low and must be replaced.
Why can't I delete a User Code on my Schlage Door locks?
If you cannot delete a user code on your Schlage door lock, possible reasons include: * You didn't press '2' after entering programming mode. * The first user code entered didn't match any current user code. * The second user code entered didn't match the first user code entered.
Why can't I change Programming Code on Schlage Door locks?
If you're unable to change the programming code on your Schlage door lock, it may be because: * You didn't press '3' after entering programming mode. * The second programming code entered didn't match the first. * The first 4-6 digits of the new programming code match an existing user code.
Why does my Schlage ALLEGION BE469 deadbolt require two attempts to lock or unlock?
If your Schlage door lock requires two attempts to lock or unlock, it's likely that the deadbolt and frame alignment is marginal. To resolve this, adjust the door and frame to achieve optimal operation.
What to do if yellow dot is flashing after entering User Code on Schlage ALLEGION BE469 Door locks?
If, after entering a user code on your Schlage door lock, the yellow dot flashes and there's a delay before the lock unlocks, it indicates that the battery is low and needs replacement.
General| Lock Type | Electronic Deadbolt |
|---|---|
| Keypad | Yes |
| Connectivity | Z-Wave |
| Battery Type | 4 AA batteries |
| User Codes | Up to 30 |
| Brand | Schlage |
| Model | BE469 |
| Battery Life | Approximately 1 year |
| Locking Mechanism | Motorized Deadbolt |
| Auto-Lock Feature | Yes |
| Alarm | Tamper Alarm |
| Finish Options | Satin Nickel, Aged Bronze |
| Smart Home Compatibility | Alexa, SmartThings, Wink |
| Finish | Satin Nickel |
| Backset | Adjustable 2-3/8" to 2-3/4" |
| Keyway | Schlage C |
| Programming | Keypad |
| Compatibility | Z-Wave compatible systems |
| Warranty | 3-year electronics, limited lifetime mechanical and finish warranty |
Instructions on how to turn the alarm on and off using the inside Schlage button.
Details on the different alarm modes (Activity, Tamper, Forced Entry) and their sounds/lights.
Information on where default programming and user codes are located on stickers.
Overview of the lock's Z-Wave capabilities and features.
Steps to include the lock into a Z-Wave network for remote control.
