83
5. SAFETY INSTRUCTION
1. This equipment, if improperly used, can cause physical and material damage. To avoid these damages, follow the instructions
below:
• This equipment may not be used by people with physical, sensorial, or mental handicaps. Or without experience or knowledge.
• People without the proper experience or knowledge may use this equipment only if properly supervised or instructed to it’s use
by someone who is liable for his or her safety.
• This equipment may not be used by children under any circumstances.
• Do not use your eqipment while tired, under the infl uence of medication, alcohol or drugs. Lack of attention during operation may
result in serious personal injury;
• Can cause mechanical or electrical interference on nearby sensitive equipments;
• Must be installed and operated in places that are ventilated and protected against moist presence and water falling.
2. The equipment model must be chosen in compliance with the established use. don’t exceed maximun capacity, if required, acqui-
re a more suitable tool for the application. This will increase the effi ciency and safety in the work;
3. Always use suitable personal protective equipment (PPE), as each application, such as dust glasses and masks, non-skid safety
shoes and ear protection. This reduces the risks against personal injury;
4. As any motorized equipment, this product emits noise during operation. The recommendation is to install and/or use it in an en-
closed place or away from others in the neighborhood, in order to reduce the impacts caused by noise pollution;
5. Not use long wear clothing, or jewelry that may come into contact with the moving part of the tool during use. If you have
long hair, contain it before using the tool;
6. While in use, this equipment has electrical components and hot moving parts;
7. To reduce the risk of electrical shock;
• For protection against electric shock, it is recommended to install a residual current circuit breaker. Consult an electrician to
select and install this safety device;
• Do not use the equipment barefoot, in wet or very humid places, do not touch metal surfaces attached to the ground or grounded,
such as pipes, motors, gutters, fences, windows, doors, metal gates, etc, this increases the risk of electric shock;
• Before cleaning or performing maintenance, disconnect the machine from the electrical network;
• Do not make splices in the cord. If required, ask for a power cord replacement at the nearest Schulz Authorized Dealer (The costs
of power cable replacement are the sole responsibility of the customer).
• Power outlet must be compatible to the tool plug. To reduce the risk of shock, do not change the plug characteristics and do not
use adapters. If required, replace the outlet with a plug suitable model.
• Do not use your electric equipment in explosive atmospheres (gas, fl ammable liquid or dust). The motor generate sparks that
may cause explosion;
• Make sure the power trigger is in the “off” position before connecting the equipment to the power grid.
8. Do not alter the settings of the valve, once come preset from the factory, if some adjustment is necessary, use the service of the
nearest SCHULZ AUTHORIZED DEALER.
9. Never surpass the maximum presence indicated on the equipment identification plate/sticker.
10. The compressed air might contain pollutants that will cause harm to the health of humans, animals, ambient or foods,
among others. The compressed air must be treated with adequate filters, according to application and use requirements.
Consult the factory or a SCHULZ AUTHORIZED DEALER. for more information.
11. Do not allow the compressor to come in contact with any flammable substances;
12. Remove all adjustment tools before turning your equipment on. A tool or part stuck in moving of the equipment may cause serious
injuries;
13. Never clean the equipment with solvents or any other flammable substances, use a neutral detergent.
14. In presence of any equipment abnormally, suspend its operation immediately and contact the nearest SCHULZ AUTHORIZED
DEALER.
15. Never perform repairs or welding jobs on compressed air or refrigeration pipelines. In case of leakage, cracks, or deterioration
by way of corrosion, immediately shutdown the operation of the SRS - Compressed Air Dryer and immediately seek technical
assistance from an accredited Schulz Authorized-Technical/Distributor for this equipment.
16. Make sure that the product’s maintenance and operation are performed by a properly trained and qualified professional.
To Next Page
Loading...