Using the Intemet
Example
5 Press A/V to select "Push button", and then press
ENTER.
o To configure the setting via PC, select "PIN code".
Follow the on-screen instructions and the operation
manual of the access point to configure the settings.
6 Select "Next" to complete the settings.
o The connection process starts and the WPS button on
the access point can be pressed.
7 Press the WPS button on the access point.
o Pressing the WPS button displays a confirmation
screen. Please wait until a connection is established.
8 When a connection is established, the connection
details are displayed. Press ENTER.
1 Press
press
2 Press
press
3 Press
press
4 Press
press
MENU to display the MENU screen, and then
_/1_ to select "Initial Setup".
A/V to select "lntemet Setup", and then
ENTER.
A/V to select "Network Setup", and then
ENTER.
A/T to select "Connection Type", and then
ENTER.
5 Press _/1_ to select "Wired" or "Wireless", and
then press ENTER.
o Ifyou select "Wired", the signal is detected and setup
is performed automatically. Use "IP Setup" to check
and change the settings as necessary. (See page 68.)
, Ifyou select "Wireless", use "Wireless Setup" to
configure the access point settings.
If your access point supports Wi-Fi Protected Setup
(WPS), it is recommended that you use this function
for the wireless connection. You can press the WPS
button on the access point to configure the settings
automatically.
o Thename ofthe WPS button function may differdepending
on the access point. See the operation manualof the
access point for details.
1 Confirm the current settings in "Connection Type".
o If "Wired" isselected, press 4/_ to select"Wireless".
2 Press A/T to select "Wireless Setup", and then
press ENTER.
o Confirm the settings.
press MENU to exit.
o Ifyou are configuring
time or changing the
3 Press 4/_ to select
ENTER.
4 Press A/T to select
ENTER.
o To select and register anaccess point manually,select
"Search"or "ManualSetup" and make the necessary
settings.
If each setting item is correct,
the wireless setup for the first
settings, go to step 3.
"Change", and then press
"WPS", and then press
If you do not want other people to connect to the
Intemet in your absence, you can make settings to
keep the TV away from the Intemet.
1 Press MENU to display the MENU screen, and then
press _/1_ to select "Initial Setup".
2 Press A/V to select "lntemet Setup", and then
press ENTER.
3 Press A/V to select "Interactive Service", and then
press ENTER.
Input the 4-digit secret number by using 0-9.
4 Press 4/1_ to select "No", and then press ENTER.
o If you wantto allow Intemetconnection, select "Yes",
and then press ENTER.
5 Press MENU to exit.
1 Press APPS to display the application window.
2 Press A/T/_I/_ to select "AQUOS NET" and then
press ENTER.
If "_'_" is displayed after you connect to the Intemet,
check your TV's network settings and connection.
You can also display the AQUOS NET screen by
pressing FAY APP on the remote control unit. See
page 35 for details on the FAV APP key Assign
function.
3 Press APPS and select "AQUOS NET" once or
twice to switch to the TV + Web or Web screen.
When the original home page appears, now you are
connected to the Intemet.
o If you have failed to connect to the Intemet in the above
operation, then an error message will appear. In this case,
press EXIT to exit from the connected TV feature to make
changes to the network settings (see page 68).
o If you still cannot connect to the Intemet, please consult
your Intemet service provider or telephone company.
o When an application is used, you cannot make settings for
"Intemet Setup".
If you need to make the settings of "lntemet Setup", press
EXIT to exit from the connected TV feature.
Q- 67
To Next Page
Loading...
