Sharp AR-5516

AR-5520 SIMULATIONS 7-5
06 01 Paper feed solenoid operation
check
When this simulation is executed, the sub code is displayed on the 7-seg display and the lamp
corresponding to the solenoid lights up.
Select a solenoid with the [TRAY SETTING] key (the lamp corresponding to the solenoid lights up)
and press the [START] key, and the machine repeats operation of ON for 500ms and OFF for 500ms.
This operation is repeated 20 times.
After that, the machine goes into the sub code entry standby mode.
02 Resist roller solenoid operation
check
When the [START] key is pressed in the sub code input state, the resist solenoid (RRS) turns ON for
500ms and OFF for 500ms. This operation is repeated 20 times.
After completion of the process, the machine goes into the sub code input standby mode.
10 1st tray semicircular roller cleaning The main motor is rotated to rotate the semicircular roller of the 1st tray one turn to face the
semicircular roller down. (Remove the developing layer when performing this operation.)
During this process, the sub code is displayed on the display section.
After completion of the process, the machine goes into the sub code input standby mode.
07 01 Warm-up display and aging with
jam
Copying is repeated to make the set copy quantity. When this simulation is executed, warm-up is
started and warm-up time is counted up every second from 0 and displayed. After completion of
warm-up, warm-up time count is stopped. When the [CA] key is pressed, the START indicator lights
up. After that, when the copy quantity is inputted with keys and the [START] key is pressed, copying
is repeated to make the set copy quantity. (Intermittent 0 sec)This simulation is canceled by turning
off the power or performing a simulation that executes hardware reset.
06 Intermittent aging Copying is repeated to make the set copy quantity. When this simulation is performed, warm-up is
performed and the START indicator is lighted. Enter the copy quantity with the key and press the
[START] key, and copying is repeated to make the set copy quantity, the ready state remains for 3
sec, and copying is repeated again to make the set copy quantity. These operations are repeated.
This simulation is canceled by turning off the power or performing a simulation that executes
hardware reset.
08 Shifting with warm-up display
(Shifting similar to pressing the CA
key)
When the simulation code is entered, warm-up is started and warm-up time is counted up every
second from 0 and displayed. When the [CA] key is pressed during counting up, the display section
displays "0" and count-up process stops. However, warm-up is continued.
After completion of warm-up, counting is stopped. Press the [CA] key to terminate the simulation
mode. (This simulation is similar to SIM07-01, but without the aging function.)
08 01 Developing bias output When the [START] key is pressed, the developing bias signal is turned ON for 30 sec.
However, to calculate the actual output value is calculated, execute SIM25-01.
After completion of the process, the machine goes into the sub code input standby mode.
02 Main charger output (Grid = HIGH) When the [START] key is pressed, the main charger output is supplied for 30 sec in the grid voltage
HIGH mode. After completion of the process, the machine goes into the sub code input standby
mode.
03 Main charger output (Grid = LOW) When the [START] key is pressed, the main charger output is supplied for 30 sec in the grid voltage
LOW mode. After completion of the process, the machine goes into the sub code input standby
mode.
06 Transfer charger output Select an output mode with the [AUTO/TEXT/PHOTO] key and press the [START] key. The transfer
charger output is delivered for 30 sec in the selected mode.
After 30 sec of transfer charger output, the machine goes into the sub code entry standby mode.
Main
code
Sub
code
Contents Details of operation
LED Solenoid
Main tray indicator
2nd tray indicator
3rd tray indicator
4th tray indicator
Bypass tray indicator
Misfeed indicator(2nd tray)
Misfeed indicator(Copier) & Misfeed
indicator(2nd tray)
1st tray paper feed solenoid
* 2nd tray paper feed solenoid
* 3rd tray paper feed solenoid
* 4th tray paper feed solenoid
Bypass tray solenoid
* 2nd tray transport solenoid
* 3rd tray transport solenoid
•Small size is Letter R (A4R) or smaller.
* Duplex model only
LED Output mode
AUTO indicator
TEXT indicator
AUTO indicator & PHOTO indicator
TEXT indicator & PHOTO indicator
AUTO & TEXT & PHOTO indicator
Normal size width: Front surface
Normal size width: Back surface*
Small size width: Front surfac
Small size width: Back surface*
Bypass tray indicator mode