Sharp DV-RW550U - Disassembly;Assembly Procedures of Deck Mechanism

2-4-1
E9434DA
DISASSEMBLY/ASSEMBLY PROCEDURES OF DECK
MECHANISM
Before following the procedures described below, be sure to remove the deck assembly from the cabinet. (Refer to
CABINET DISASSEMBLY INSTRUCTIONS.)
All the following procedures, including those for adjustment and replacement of parts, should be done in Eject mode;
see the positions of [41] and [42] in Fig. DM1 on page 2-4-3. When reassembling, follow the steps in reverse order.
No.
/LOC.
STEP
No.
ING
START-
PART
REMOVAL INSTALLATION
Fig. No.
UNPLUG/DESOLDER
UNLOCK/RELEASE/
REMOVE/*UNHOOK/
CONDITION
ADJUSTMENT
[1] [1] Guide Holder A T DM3 2
(
S-1
)
[2] [1]
Assembly
Cassette Holder
TDM4
[3] [2] Slider
(
SP
)
TDM5
(
S-1A
),
*
(
L-1
)
[4] [2] Slider
(
TU
)
TDM5 *
(
L-2
)
[5] [4] Lock Lever T DM5 *
(
L-3
),
*
(
P-1
)
[6] [2] Cassette Plate T DM5
[7] [7] Cylinder Assembly T DM1
,
DM6 Desolder
,
3
(
S-2
)
[8] [8]
Assembly
Loading Motor
TDM1
,
DM7
2
(
S-3
)
Desolder
,
LDG Belt
,
[9] [9] ACE Head Assembly T DM1
,
DM7
(
S-4
)
[10] [2]
Assembly
Tape Guide Arm
TDM1
,
DM8-1 *
(
P-2
)
[11] [10] C Door Opener T DM1
,
DM8-1
(
S-4A
),
*
(
L-4
)
[12] [11] Pinch Arm
(
B
)
T
DM8-2
DM1
,
DM8-1
,
*
(
P-3
)
[13] [12]
Assembly
Pinch Arm
(
A
)
T
DM8-2
DM1
,
DM8-1
,
[14] [14] FE Head T DM1
,
DM9
(
S-5
)
[15] [15] Prism T DM1
,
DM9
(
S-6
)
[16] [2]
,
[15] Sensor Gear T DM1
,
DM9
[17] [2] Slider Shaft T DM10 *
(
L-5
)
[18] [17] C Drive Lever
(
SP
)
TDM10
[19] [17] C Drive Lever
(
TU
)
TDM10
(
S-7
),
*
(
P-4
)
[20]
[10]
[7]
,
[8]
,
Capstan Motor B DM2
,
DM11 3
(
S-8
),
Cap Belt
[21] [21] Clutch Assembly B DM2
,
DM12
(
C-1
)
[22] [22] Cam Holder Assembly B DM2
,
DM12 *
(
L-6
)
[23] [23] Cam Gear
(
B
)
BDM2
,
DM12
(
C-2
),
*
(
P-5
)
[24] [24] Mode Gear B DM2
,
DM13-1
(
C-3
)
[25]
[24]
[21]
,
[23]
,
Mode Lever B
DM13-2
DM2
,
DM13-1
,
(
C-4
),
*
(
L-8
)
[26] [22] Worm Holder B DM2
,
DM13-1
(
S-9
),
*
(
L-9
),
*
(
L-10
)
[27] [26] Pulley Assembly B DM2
,
DM13-1
[28] [25]
,
[26] Cam Gear
(
A
)
B
DM13-2
DM2
,
DM13-1
,