Sharp MX-C300F - Page 119

MX-C250 SIMULATION 6 – 42
44-29
Purpose
Setting
Function (Purpose)
Used to set the operating conditions of the
process control during a job.
Section
Process
Operation/Procedure
1) Select an item to be set with Arrow keys.
2) Enter the set value with 10 keys.
3) Press [OK]/[START] key.
The set value in step 2) is saved.
NOTE:
Set the items to the default values unless a change is spe-
cially required.
44-31
Purpose
Adjustment/Setup
Function (Purpose)
Used to adjust the OPC drum phase. (Man-
ual adjustment)
Section
Process
Operation/Procedure
NOTE:
For the OPC drum phase adjustment, do not use this simu-
lation, but use SIM50-22 (auto adjustment).
1) Select item A with Arrow key.
2) Enter the value corresponding to the adjustment pattern with 10
keys.
3) Press [OK]/[START] key. (The adjustment pattern is printed out.)
4) Select an adjustment pattern whose deflection is within two
scale lines on the adjustment pattern of C,M, Y colors.
5) Select item B with Arrow keys.
6) Enter the adjustment pattern sheet number selected in proce-
dure 4).
7) Press [OK]/[START] key.
8) The adjusted adjustment pattern is printed.
44-37
Purpose
Adjustment/Setup
Function (Purpose)
Used to set the development bias correc-
tion level in the continuous printing opera-
tion.
Section
Operation/Procedure
1) Select an item to be set with Arrow keys.
2) Enter the set value with 10 keys.
3) Press [OK]/[START] key.
The set value in step 2) is saved.
NOTE:
When the print density is varied in the continuous printing
operation, this simulation is used.
44-43
Purpose
Data display
Function (Purpose)
Used to display the identification informa-
tion of the developing unit.
Section
Developing system
Operation/Procedure
The identification number and the identification signal level of the
developing unit are displayed.
Item/Display Content Setting range
Default
value
1COPY
During copy
job
0 - 2
0
No execu-
tion
2
2 PRINTER During print job 1 HV only 2
3FAX
During FAX
print job
2HV -> HT
2
4
SELF
PRINT
During self
print
2
2
Item/Display Content
Setting
range
Default
value
1 PRINT MODE Print mode
1 : Deflection check pattern print for every 45 degrees (8-sheet print) 
1 - 3
3
(SET
VALUE)
2 : Deflection check pattern print for every 90 degrees (4-sheet print) 
3 : Deflection check pattern print at the set value (1-sheet print)
2 COLOR
Phase adjustment value
BK -> CL
Angle step 0 (1)  45 (2)  90 (3)  135 (4)  180 (5)  225 (6)  270 (7) 
315 (8)
1 - 8 1
3 PAPER Tray selection
1 : Manual paper feed
1 -3 2 2 : 1 CS
3 : 2CS
Item Display Contents Range
Default
value
1MUL_MC_ADJ
MC bias correction in the
continuous printing is
enabled / disabled.
0-1 0
Item/Display Content
Display
range
1 DVCH KIND K
K color development unit identifica-
tion number
1 - 5
2 DVCH KIND C
C color development unit identifica-
tion number
1 - 5
3 DVCH KIND M
M color development unit identifica-
tion number
1 - 5
4 DVCH KIND Y
Y color development unit identifica-
tion number
1 - 5
5DVCH_AD_K
K color developing unit identification
number AD value
0 - 255
6DVCH_AD_C
C color developing unit identification
number AD value
0 - 255
7DVCH_AD_M
M color developing unit identifica-
tion number AD value
0 - 255
8DVCH_AD_Y
Y color developing unit identification
number AD value
0 - 255