MX-C250 SIMULATION 6 – 68
67-34
Purpose
Adjustment/Setup
Function (Purpose)
Used to set the density correction in the
printer high density section. (Support for
the high density section tone gap)
Section
Printer
Operation/Procedure
1) Enter the set value with 10 keys.
2) Press [OK]/[START] key. The set value in step 1) is saved.
- When tone gap is generated in the high density section, set
items 1 and 2 to "0."
The density in the high density section is decreased, but tone
gap is reduced.
- To increase the density in the high density section further, set
items 1 and 2 to "1.
The tone gap may occur in high density part.
67-36
Purpose
Adjustment/Setup
Function (Purpose)
Used to adjust the density in the low den-
sity section.
Section
Printer
Operation/Procedure
1) Enter the adjustment value using the 10 keys.
2) Press [OK]/[STSRT]. key.
When the adjustment value is increased, the low density images
are strongly reduced. When the adjustment value is decreased, the
low density are images are weakly reproduced.
When tone gap is generated in the low density section (highlight
section), changing this adjustment value may improve the trouble.
67-52
Purpose
Adjustment
Function (Purpose)
Used to reset the printer color balance
adjustment (adjustment for each dither) to
the default value. (The set values of SIM67-
33 are set to the default values.)
Section
Operation/Procedure
This simulation is used to reset the adjustment values of SIM67-54
and SIM67-33 to the default values.
1) Select an item to be reset to the default (for each dither) with 10
keys. .
To reset the adjustment values of all the items, select [ALL].
2) Press [OK]/[START] key.
6 POINT6 Point 6 0 - 255 128 120
7 POINT7 Point 7 0 - 255 128 114
8 POINT8 Point 8 0 - 255 128 105
9 POINT9 Point 9 0 - 255 128 95
10 POINT10 Point 10 0 - 255 128 82
11 POINT11 Point 11 0 - 255 128 64
12 POINT12 Point 12 0 - 255 128 57
13 POINT13 Point 13 0 - 255 128 62
14 POINT14 Point 14 0 - 255 128 75
15 POINT15 Point 15 0 - 255 128 114
16 POINT16 Point 16 0 - 255 128 128
17 POINT17 Point 17 0 - 255 128 128
Item Display Content
1 HEAVYPAPER_K Heavy paper K
2 HEAVYPAPER_C Heavy paper C
3 HEAVYPAPER_M Heavy paper M
4 HEAVYPAPER_Y Heavy paper Y
5 SCREEN1_K Standard/Photo
6 SCREEN1_C Standard/Photo
7 SCREEN1_M Standard/Photo
8 SCREEN1_Y Standard/Photo
9 SCREEN2_K Standard/Photo
10 SCREEN2_C Standard/Photo
11 SCREEN2_M Standard/Photo
12 SCREEN2_Y Standard/Photo
13 SCREEN3_K High quality/Photo
14 SCREEN3_C High quality/Photo
15 SCREEN3_M High quality/Photo
16 SCREEN3_Y High quality/Photo
17 SCREEN4_K High quality/Photo
18 SCREEN4_C High quality/Photo
19 SCREEN4_M High quality/Photo
20 SCREEN4_Y High quality/Photo
21 SCREEN5_K B/W Standard K
22 SCREEN6_K B/W High quality/Photo K
23 SCREEN7_K B/W High quality/Photo K
24 SCREEN8_K B/W Toner Save K
0 Enable
1Disable
Item/Display Content
Set-
ting
range
Default
value
1
CMY PROHIBIT
(0: ENABLE
1: DISABLE)
0
CMY engine highest
density correction
mode : Enable
0 - 1 0
1
CMY engine highest
density correction
mode : Disable
2
K PROHIBIT
(0: ENABLE
1: DISABLE)
0
K engine highest
density correction
mode : Enable
0 - 1 1
1
K engine highest
density correction
mode : Disable
Item/Display Content
Set-
ting
Range
Heavy
paper or
screen1 to 7
Screen 8
Default
value
Default
value
Item Display Content Range Default
value
1 A PATCH INPUT A patch input value 0 - 13 1
Item Display Content Note
1 ALL All dither value
2 HEAVY PAPER Heavy paper dither value
3 1BIT 1 bit dither value
4 2BIT 2 bit dither value
5 B/W Monochrome dither value
To Next Page
Loading...
Need help?
General
