MX-FX11 FAX SOFTWARE SWITCH 2 – 16
System settings (Line/Other)
93 6 Internet FAX Setting of the 1W
energy-save mode
entering time when the
POP3 confirmation
function is enable.
Setting whether the machine enters the 1W energy-saving mode/1W nighttime
mode according to the frequency confirmation time in the POP3 server
frequency confirmation when the I-FAX function is ON.
"0": 3 minutes
"1": No limit
Incase of "0" above, if the POP3 server frequency confirmation time is within 3
minutes, the machine does not enter the 1W mode but enters the pseudo
energy-saving mode.
In case of "1", the machine enters the pseudo energy-saving mode regardless
of the POP3 server frequency confirmation time.
In addition, since the default of the POP3 server frequency confirmation time is
5 minutes, the machine enters the 1W mode under the normal conditions. In
order to keep the machine in the pseudo energy-saving mode, perform either of
the following two methods:
• Change the POP3 server frequency confirmation timing to 3 minutes or less.
• Change this SSW to "1."
*2
7, 8 Not used
94 1-8 Not used
95 1 Internet FAX Size selection for
internet FAX reception
Setting is made to select "Paper individual setting" or "Paper combination
setting" in I-FAX reception.
1: 1: Paper individual setting (Follows SW95-2 - 6.)
0: 0: Paper combination setting (Follows SW91-4 - 5.) (Default)
* This soft SW is added according to requests from the market for combination
of paper selection which is not available with SW91-4 and 5.
Example: Print in B4 only
2-6 Internet FAX Size selection for
internet FAX reception
(Paper individual
setting)
Setting is made to select whether each paper size is included as an option of
the paper selection in the individual selection of paper when receiving I-FAX.
"Selected" → The paper size is included as an option of paper selection.
"Not selected" → The paper size is not included as an option of paper selection.
* This setting is valid when SW95-1 "Size selection for internet FAX reception"
is set to "1: Paper individual setting". When, however, all of SW95-2 - 6 are
set to "1: Not selected", SW95-1 functions as "0."
7 Function White paper skip
confirmation
Process after message
time out
If the white paper skip function is set, when [START] button is pressed, the
message is displayed confirming the document quantity actually scanned and
that to be sent. This setting is made to select the job 60 sec after the above
state.
"1": The send job is performed.
"0": The job is cancelled. (Default)
*2
8 Function Process after time out
of the document
quantity count
confirmation
If the document quantity count function is ON, when scanning is completed with
the document feed unit, the massage of the scanned document quantity is
displayed. This setting is made to select the job 60 sec after the above state.
"1": The send job is performed.
"0" The job is canceled. (Default)
*2
96
-
98
1-8 Not used
SW
No.
Bit
No.
Item SW selection and function System settings
SW
No.
Bit
No.
Item SW selection and function System settings
99 1, 2 Calling Tone/Pulse initial
setting (Dial call signal
setting)
This is set according to dial type.
"00": 10PPS (pulse)
"01": 20PPS
"10": TONE
"11": TONE
Other than China/Thailand: If "20pps" is set, adopt the initial TONE.
FAX initial setting/
Setting
3-6 Calling Pause time setting
(between dials)
This sets the time per pause inputted during dialling.
The pause time can be set from 1 to 15 seconds in 1-second increments by
binary inputting N over the range of 0 to 15 (1 second x N).
If a value outside the setting range (or "0000") is set, the initial value of 2
seconds is reverted to.
FAX initial setting/
Adjustment value
7, 8 Calling PBX setting Setting to determine whether or not to send out ID or Flash before dialing.
Functions only in Germany and France.
In other countries, this setting is fixed to "OFF".
"00": OFF
"01": Flash
"10": ID
"11": Not used (OFF)
The setting other than the above would be granted as the default.
FAX initial setting
To Next Page
Loading...
