MX-FX11 FAX SOFTWARE SWITCH 2 – 17
100 1-4 Calling ID (number) setting
<Input the 1st digit
when dial inputting and
dialing>
Conduct ID No. setting when the PBX function is valid.
Valid when ID is set using SW99-7, 8.
The initial value of 0 is reverted to if a value outside of the setting range (10 -
15) is set.
FAX initial setting
5-8 Calling ID (number) setting 2
<Input the 2nd digit
when dial inputting and
dialing>
Conduct ID No. setting when the PBX function is valid.
Valid when ID is set using SW99-7, 8.
When 10 - 12, 14, 15 are designated, do not use numbers with those digits.
"-" when 13 is set.
FAX initial setting
101 1-4 Calling ID (number) setting 3
<Input the 3rd digit
when dial inputting and
dialing>
Conduct ID No. setting when the PBX function is valid.
Valid when ID is set using SW99-7, 8.
When 10 - 12, 14, 15 are designated, do not use numbers with those digits.
"-" when 13 is set.
FAX initial setting
5-8 Call arrival Distinctive ring (DRD
setting)
Setting to determine whether or not to execute FAX arrival call by the distinctive
ring.
Even if a call signal other than the set pattern is detected, there will be no
automatic arrival call.
"0000": OFF
"0001": STANDARD
"1000": Pattern 1
"0100": Pattern 2
"1100": Pattern 3
"0010": Pattern 4
"1010": Pattern 5
"0110": ON (Australia)
"1110": ON (New Zealand)
"1001": ON (Hong Kong)
When contents other than the above are set, the initial value is reverted to.
FAX initial setting/
Setting
102 1 Not used
2-5 Call arrival Setting of the number
of automatic reception
calls
Set the number of call sounds until the start of receiving (holding of the line)
when automatic reception is set.
This can be set from 0 to 15 (Europe/Indonesia/Thailand: 0 to 9, Australia/New
Zealand: 2 to 4) times by binary inputting.
If 0 is set, the call sound will not be sounded. (However, this does not include
the nighttime FAX mode.)
FAX reception
setting/
Setting
6 Call arrival Setting for changing
over to automatic
reception during
manual reception
Setting to determine whether or not to initiate automatic reception after the
ringer sounds a certain number of times when manual reception is set.
"0": Prohibited (do not changeover)
"1": Permitted (changeover)
FAX reception
setting/
Setting
7, 8 Not used
103 1-5 Call arrival Setting of the number
of calls for changing
over from manual to
automatic reception
Set the number of calls before changing over to automatic reception when in
the manual reception mode.
Functions only in France.
This functions when the "Setting for changing over to automatic reception
during manual reception" (SW71-6) is valid.
Setting can be made over the range of 1 to 9 times in 1 time increments by
binary inputting.
The initial value is reverted to if a value outside of the setting range is set.
FAX reception
setting/
Setting
6 Communication ECM (valid except
during V.34: reflected
in the V.21 DIS/DCS/
DTC)
Setting to determine whether or not to execute the error re-send mode.
However, this is only valid when communication is other than V.34.
"0": Yes. Set with ECM function.
"1": No. Set with no ECM function.
ECM is on during communication in the V.34 mode.
FAX initial setting
7 Function Change from the
image send screen to
the copy screen
Setting to determine whether or not to automatically change from the image
send screen to the copy screen.
When changing over, if no keys are operated for 20 seconds after pushing the
final key in the image send mode, the copy mode will be automatically switched
to.
If there is no changeover, the machine will remain in the image send mode and
not switch to the copy mode.
"0": Do not change over
"1": Change over
*3
Operation setting
8 Function Image quality setting
when saving (FAX)
Setting to determine whether or not to make filed image quality valid (initial
setting for image quality selection when transmitting filed document files by
FAX)
"0": Do not apply
"1": Apply
Operation setting
SW
No.
Bit
No.
Item SW selection and function System settings
To Next Page
Loading...
