Sharp MX-FX11

MX-FX11 FAX SOFTWARE SWITCH 2 – 18
104 1-4 Function Image quality priority
selection (standard
image quality setting)
Setting to determine the initial setting for image quality selection when reading
documents on the FAX.
"0000": Ordinary lettering
"0001": Small lettering
"0010": Fine
"0011": Very fine
"0101": Small lettering, medium tone
"0110": Fine, medium tone
"0111": Very fine, medium tone
"Ordinary lettering" (initial value) is reverted to if a value outside of the setting
range is set.
Operation setting
5 Function Received data printing
hold (FAX/Internet
FAX)
Setting to determine whether or not to store data received by FAX/Internet FAX
in the memory without outputting it.
"0": Do not hold
"1": Hold
Operation setting
6 Function Saving the setting
contents for a certain
period after completion
of scanning
Setting to determine whether the set values of the destination and various
functions are saved without returning to the default values or not when
reservation is completed on the image send screen.
"0": The set values are not saved.
"1": The set values are saved.
Operation setting
7 Not used
8 Function Default finish stamp
setting
Setting to determine whether the finish stamp is used or not after completion of
document scan when the document feed unit is used.
"0": NO (The finish stamp is not used.)
"1": YES (The finish stamp is used.)
Operation setting
105 1-4 Function Speaker volume when
on-hook (Speaker
volume during DTMF
sending)
This sets speaker volume for when the on-hook button is pushed.
The sound volume is set with a value. The greater the value is, the greater the
sound volume is.
Setting range is 1 (small) to 15 (large) by binary input.
When it is set to "0," it is considered as setting to the default.
FAX initial setting
5-8 Function Call sound volume Irrespective of whether there is a handset, this sets the volume of the call
sound that is sounded when a signal arrives.
The sound volume is set with a value. The greater the value is, the greater the
sound volume is.
Setting range is 1 (small) to 15 (large) by binary input.
When it is set to "0," there is no sound (OFF).
FAX initial setting
106 1-4 Function Line monitor volume
setting
Set the speaker volume during line monitoring.
The sound volume is set with a value. The greater the value is, the greater the
sound volume is.
Setting range is 1 (small) to 15 (large) by binary input.
When it is set to "0," there is no sound (OFF).
FAX initial setting
5-8 Function Volume of the
transmission
completion sound
(Volume of the
successful
transmission sound)
Set the volume of the completion sound outputted from the speaker upon
completion of FAX transmission.
When sending is succeeded, a sound is generated by this setting.
The sound volume is set with a value. The greater the value is, the greater the
sound volume is.
Setting range is 1 (small) to 15 (large) by binary input.
When it is set to "0," there is no sound (OFF).
FAX initial setting
107 1-4 Function Volume of the
communication error
completion sound
(Volume of the
transmission and
reception error sound)
This sets the volume of the completion sound outputted from the speaker upon
completion of FAX communication error.
The sound volume is set with a value. The greater the value is, the greater the
sound volume is.
Setting range is 1 (small) to 15 (large) by binary input.
When it is set to "0," there is no sound (OFF).
FAX initial setting
5-8 Function Volume of the
reception completion
sound (Volume of the
reception completion
sound)
This sets the volume of the completion sound outputted from the speaker upon
completion of FAX reception.
When receiving is succeeded, a sound is generated by this setting.
The sound volume is set with a value. The greater the value is, the greater the
sound volume is.
Setting range is 1 (small) to 15 (large) by binary input.
When it is set to "0," there is no sound (OFF).
FAX initial setting
SW
No.
Bit
No.
Item SW selection and function System settings