Sharp MX-FX11

MX-FX11 FAX SOFTWARE SWITCH 2 – 19
108 1, 2 Function Tone of the successful
transmission sound
This sets the tone sounded when transmission is successful.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)
FAX initial setting
3, 4 Function Tone of the
transmission and
reception error sound
This sets the tone sounded when there is a transmission and reception error.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)
FAX initial setting
5, 6 Function Tone of the reception
sound
This sets the tone sounded upon completion of reception.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)
FAX initial setting
7 Function Auto startup mode In the case where FAX or Internet FAX is received during nighttime mode or
simulated mode, if this setting is ON, the received document will be outputted
when the machine becomes able to output. When OFF, the machine will
receive the data by proxy without outputting the document, but it will output the
received document when the panel power SW is ON.
"0": Setting (setting for automatically starting up the main unit and outputting)
"1": Release (setting for storing in the memory without starting up the main unit)
FAX initial setting
8 Function Digital line net setting When this is set to "1: ON", "-15dBm" is set regardless of the soft switch setting
in the signal send level on the FAXBOX side.
For MX-2310 series, the operation is made when this switch is set to ON.
FAX initial setting
109 1-3 Function Setting of the
successful
transmission sound
time
This sets the time the tone is sounded when transmission is successful.
"000": 2.0 seconds
"001": 2.5 seconds
"010": 3.0 seconds
"011": 3.5 seconds
"100": 4.0 seconds
The initial value is reverted to if a value outside of the setting range is set.
FAX initial setting
4-6 Function Setting of the reception
sound time
This sets the time the tone is sounded upon completion of reception.
"000": 2.0 seconds
"001": 2.5 seconds
"010": 3.0 seconds
"011": 3.5 seconds
"100": 4.0 seconds
The initial value is reverted to if a value outside of the setting range is set.
FAX initial setting
7 Function Setting of the time of
the transmission/
reception error sound
Transmission error sound sounding interval
"0": Every 0.3 seconds
"1": Every 0.7 seconds
Sounding time and paper feeding time are the same.
FAX initial setting
8 Function Changing the file name
in the FAX reception
data transfer into TSI
information
Setting is made whether the file name in the FAX reception data transfer is
changed into TSI information or not.
0: Not changed
1: Changed
*3
110 1, 2 Print Communication results
sheet print settings (for
ordinary transmission)
<FAX only>
This sets outputting of the communication results sheet following transmission
(excluding successive broadcast, successive polling and relay broadcast
transmission).
"00": Do not print
"01": Always print
"10": At times of transmission failure
The initial value is reverted to if a value outside of the setting range is set.
FAX initial setting
3, 4 Print Setting of the
communication results
sheet printing (at times
of broadcast
transmission)
This sets outputting of the communication results sheet at times of successive
broadcast, successive polling and relay broadcast transmission.
"00": Do not print
"01": Always print
"10": Failed transmission address
The initial value is reverted to if a value outside of the setting range is set.
FAX initial setting
5, 6 Print Communication results
sheet print setting
(when receiving)
<FAX only>
This sets outputting of the communication results sheet for when
communications are received (excluding confidential communications).
"00": Do not print
"01": Always print
"10": At times of error
The initial value is reverted to if a value outside of the setting range is set.
FAX initial setting
7 Print Report output (when
receiving confidential
communications)
<FAX only>
Setting to determine whether or not to output the communication results sheet
(receiving) when confidential communications are received.
"0": Print
"1": Do not print
This only functions when the communication results sheet print setting
(receiving) is set to be outputted.
FAX initial setting
8 Not used
SW
No.
Bit
No.
Item SW selection and function System settings