EasyManuals Logo

Sharp PN-E702 User Manual

Sharp PN-E702
57 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #15 background imageLoading...
Page #15 background image
15
E
Preparing the Remote Control Unit
Installing the batteries
1. Pressthecovergentlyandslideitinthedirectionofthe
arrow.
2. Seetheinstructionsinthecompartmentandputinthe
suppliedbatteries(R-6(“AA”size)x2)withtheirplus(+)
andminus(-)sidesorientedcorrectly.
3. Closethecover.
TIPS
• Whenthebatteriesbecomeexhausted,replacethemwith
new(commerciallyavailable)batteries.
• Thesuppliedbatteries(R-6(“AA”size)x2)maybecome
exhaustedquicklydependingonhowtheyarestored.
• Ifyouwillnotbeusingtheremotecontrolforalongtime,
remove the batteries.
• Usemanganeseoralkalinebatteriesonly.
Remote control operation range
Theoperationrangeoftheremotecontrolunitisapprox.16.4
feet(5m)atanangleofapprox10°fromthecentertothetop/
bottom/right/left of the remote control sensor.
10°1
10°
10°
Remote
control sensor
16.4
feet
(5 m)
TIPS
• Donotexposetheremotecontrolunittoshockbydropping
or stepping on it. This could lead to a malfunction.
• Donotexposetheremotecontrolunittoliquids,anddonot
place it in an area with high humidity.
• Theremotecontrolunitmaynotworkproperlyiftheremote
control sensor is under direct sunlight or strong lighting.
• Objectsbetweentheremotecontrolunitandtheremote
control sensor may prevent proper operation.
• Replacethebatterieswhentheyrunlowasthismay
shorten the remote control’s operation range.
• Ifauorescentlightisilluminatedneartheremotecontrol
unit, it may interfere with proper operation.
• Donotuseitwiththeremotecontrolofotherequipment
such as air conditioner, stereo components, etc.

Other manuals for Sharp PN-E702

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sharp PN-E702 and is the answer not in the manual?

Sharp PN-E702 Specifications

General IconGeneral
3DNo
Pixel pitch0.802 x 0.802 mm
Aspect ratio16:9
Response time6 ms
Display diagonal70 \
Separate H/V syncYes
Supported video modes1080p
Viewable size, vertical865.6 mm
Contrast ratio (dynamic)-
Contrast ratio (typical)4000:1
Display number of colors1.073 billion colors
Viewable size, horizontal1538.9 mm
Viewing angle, horizontal176 °
Display brightness (typical)450 cd/m²
Supported graphics resolutions1920 x 1080 (HD 1080)
Audio systemstereo
Analog signal format systemNTSC, NTSC 3.58, NTSC 4.43, PAL, PAL 60, SECAM
RS-232 ports2
DVI-D ports quantity0
Product colorBlack
Panel mounting interface200 x 200, 400 x 200 mm
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (typical)240 W
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)20 - 80 %
Weight and Dimensions IconWeight and Dimensions
Depth (without stand)100 mm
Width (without stand)1615 mm
Height (without stand)947 mm
Weight (without stand)50000 g

Related product manuals