XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE
3 – 4
The action is as below.
Step1) Save the below data in the folder for “Electric Journal for printing”.
Step2) After reading the information of the current sub-folder in
“SRECORD.REC” file, ECR creates the new sub-folder under
the folder for “Electric Journal Data”.
Its folder is named ASCII Character that is indicated the number
of sales data in SD Card. (Example: “1”, “2”, “3”,......)
Step3)
Save the below data in new sub-folder that is created above step.
Spet4) Create the “STATUS.REC” file in new sub-folder when all files
are saved completely.
Step5) Update the “SRECORD.REC” file for changing the structure of
sub-folder.
Step6) Clear EJ DATA on memory at ECR.
(*1) The contents of each file are same as the communication data of
“ONLINE FUNCTION”. Details of “File No.” and “Table No.” are
described in “ONLINE SPECIFICATION”. All data are converted to
use at “Customer Support Tool” software on PC.
Notes: • The file in the EJPRINT folder on SD Card is overwritten.
The message of confirmation for overwritten the file in the
EJPRINT folder on SD Card does not display.
• Each files are used only for the “Customer Support Tool” soft-
ware on PC. Any users dose not need to concern its contents.
[JOB#740] Electric journal print
ECR prints the below data that is already set in the folder for “EJPRINT Data”.
(*1) The contents of each file are same as the communication data of
“ONLINE FUNCTION”. Details of “File No.” and “Table No.” are
described in “ONLINE SPECIFICATION”. All data are converted to
use at “Customer Support Tool” software on PC.
Notes: • It is printed only the newest EJ DATA (That is saved at last by
either ECR or PC).
• Each files are used only for the “Customer Support Tool” soft-
ware on PC. Any users dose not need to concern its contents.
■ DISPLAY AND PRINT: X1/Z1 MODE)
JOB ENTRY OPERATION: (Common action for all Jobs)
--- Continue to JOB END MESSAGE (NEXT PAGE)
File Name
File/Table
No. (*1)
Field (*1)
1 EJ Data EJFILE A0
File Name
File/Table
No. (*1)
Field (*1)
1 EJ Data EJFILE A0
File Name
1 Status information STATUS.
REC
File Name
1 Record structure SRECORD
.REC
File Name
File/Table
No. (*1)
Field (*1)
1 EJ Data EJFILE A0
Key Display Print NOTE
1234567890
750 [ . ] 7 5 0.
[@/FOR] 7 5 0.
[SBTL] - The buffered keys are cleared and the message is
printed on “receipt” only.
(It is not print on “journal” and “EJ”.)
MESSAGE: MAX 8-lines
(The message is fixed in ROM.)
(Not count up CC# at this time.)
[1] 1
[CA/AT] S d
-
A C C E S S . (Count up CC#.)
DISPLAY: “ . ” is blinking
while executing job.
PRINT : JOB HEADDER is printed.
And job code is printed.
(Job code is printed only at SD jobs)
Case of EJ PRINT:
The EJ DATA is printed as same as EJ
REPORT (#700) after printing job code.
(SD ACCESS) S d
-
A C C E S S . DISPLAY : “ . ” is blinking
while executing job.
PRINT : (NON)
:
:
123456789012345678901234
(PRE-PRINT HEADDER)
!!!!!!!!!!!!!!!!!!!!!!!!
YOU SELECT SD CARD JOB
PUSH [1]-KEY to EXECUTE
PUSH [CL]-KEY to CANCEL
!!!!!!!!!!!!!!!!!!!!!!!!
Don't turn the mode key
while executing a job.
!!!!!!!!!!!!!!!!!!!!!!!!
(Issuing Receipt)
HEADER
*Z1*
05/02/2006 12:34PM
123456#1234
#750
01
BETTY___
To Next Page
Loading...
