XL-HP700 Advanced CD Playback (continued)
YES
Correct
~~
/rz\
\~-
To clear
the
programmed selections:
Press the CLEAR button
on
the remote con-
Cl Cl Cl
II
CLEAR
~~~~~i~~~~~'
~U~~~i~~~~~~~;,t~~~
t~:~~~WI·
~ ~
~
D!TI!1ffiffiffiffii'
be cleared, beginning with the last track pro-
grammed.
To cancel the programmed play mode:
While
in
the stop mode and the "MEMORY" indicator
is
lit, press the
CLEAR button
on
the remote control. The "MEMORY" indicator will
disappear and all the programmed contents will be cleared.
Adding
tracks
to
the program:
If
a program has been previously stored, the "MEMORY" indicator
will be displayed. Then follow steps 1 - 6 to add tracks. The new
tracks will be stored after the last track of the original program.
To check
which
tracks
are programmed:
While the unit
is
stopped
in
the programmed play mode, press the
~
or
~
button.
Notes:
•
Opening
the
disc
tray
automatically
cancels
the
programmed
sequence.
• Even if you press the ON/STAND-BY button to enter the stand-by
mode or change the function from CD to another, the pro-
grammed selections will not be cleared.
• During program operation, random play
is
not possible.
• Care
of
compact
discs
Compact discs are fairly resistant to damage, however mistracking
can occur due to
an
accumulation of dirt
on
the disc surface. Follow
the guidelines below for maximum enjoyment from your CD collec-
tion and player.
•
Do
not write
on
either side of the disc, particularly the non-label
side from which signals are read.
Do
not mark this surface.
•
Keep
your
discs
away
from
direct
sunlight,
heat,
and
excessive
moisture.
• Always hold the CDs by the edges. Fingerprints, dirt, or water
on
the CDs can cause noise or mistracking.
If
a CD
is
dirty or does
not play properly, clean it with a soft, dry cloth, wiping straight out
from the center, along the radius.
MEMORY/
MEMORY
ISET
a
L::)
Selected disc number
~-
:=-
II/
~~~
,_,
I
Selected track number
You can also select a track by pressing the
~
or
~
button.
4 Press the MEMORY/SET (MEMO-
_li;J
n
::J
D u
'_I
/~~~~?~~~I
RY)
button
to
save
the
track
n;f
u
,_
I U I .
number.
6 Press
the.
(CD.)
button.
tlf'
_ __ I
The total number of memory will ap-
~gf
1'111=
I'll
U
hi
\/
1:3
MEMORY
pear.
3 Press the
direct
search
buttons
on the remote control
to
select
the desired track.
2 Press one
of
the DISC SELECT
G)
- @ (© 1 - ©
3)
buttons
to
select
the desired disc.
7 Press the
~
/
c:
button
to
start
playback.
During programmed play, the DISC SELECT
G)
- @ (© 1 - ©
3)
buttons will not work.
5 Repeat steps 2 - 4
for
other
tracks. Up
to
32
tracks can be
programmed.
If
you make a mistake, the programmed tracks can be cleared
by pressing the CLEAR button.
1 While in the
stop
mode, press the
MEMORY/SET (MEMORY)
button
to
enter
the
programming save
mode.
• Programmed play
You can choose
up
to 32 selections for playback
in
the order you
like.
18
To Next Page
Loading...
