Shimano Steps BT-E6010 User Manual (English)

Other manuals for Shimano Steps BT-E6010

Original Instructions69 pages

Dealer's Manual57 pages

Questions and Answers:

J
Julie FinleySep 3, 2025
Why does the LED on my Shimano Steps BT-E6010 Bicycle Accessories charger not illuminate?
- I
  imillerSep 3, 2025
  If the LED on your Shimano Steps Bicycle Accessories charger isn't lighting up, first, check the connection of the recharging plug to the battery for any foreign objects and reinsert it. Also, if the battery is fully charged, the LED may turn off, which isn't a malfunction. Disconnect and reconnect the charger's power plug to try again. If the LED still doesn't illuminate, contact the place of purchase.
C
Christine CamposSep 2, 2025
Why is pedaling so stiff on my Shimano Steps BT-E6010?
- T
  Tammy WrightSep 2, 2025
  If you find that pedaling feels stiff with your Shimano Steps Bicycle Accessories, here are a few things to check: * Ensure your tires are inflated to the correct pressure by using a pump to add air. * Verify that the assist mode is not set to [OFF]; set it to [HIGH]. * Check if the battery is running low and charge it fully. * Make sure you didn't turn on the power while your foot was on the pedal; try turning it on again without pressure on the pedal. If the issue continues after these checks, contact the place of purchase.
S
Susan WatsonAug 23, 2025
Why is my Shimano Steps BT-E6010 cycle computer not displayed?
- D
  David FrazierAug 25, 2025
  If your Shimano Steps Bicycle Accessories cycle computer isn't displaying when you press the battery power button, consider the following: * Recharge the battery if the charge is insufficient. * Ensure the power is turned on by holding down the power button. * The power cannot be turned on while the battery is charging, so stop charging. * Ensure the cycle computer is correctly installed to the bracket. * Check if the connector of the electric wire connecting the motor unit to drive unit is not disconnected. If the issue persists, a component that the system cannot identify may be connected, or you may need to contact the place of purchase.
T
Travis AdamsAug 31, 2025
Why is assistance not being provided on my Shimano Steps Bicycle Accessories?
- B
  Bryan BakerSep 1, 2025
  If you're experiencing assistance issues with your Shimano Steps Bicycle Accessories, check these potential causes: * Ensure the battery is sufficiently charged and recharge if needed. * If riding on long slopes in summer or carrying heavy loads, turn off the power temporarily. * Assistance is not provided at speeds of 25 km/h or more, so check your speed. For issues related to incorrect connections or problems with the drive unit, cycle computer, or assist switch, contact the place of purchase.
S
Stephen WhiteAug 31, 2025
How to fix system error on Shimano Steps BT-E6010 Bicycle Accessories?
- E
  Erin FordAug 31, 2025
  If you experience a system error with your Shimano Steps Bicycle Accessories, ensure the cable is properly connected and not loose. If the problem persists, it's recommended to contact the place of purchase.
T
Tiffany GriffithAug 30, 2025
Why won't my Shimano Steps Camera Accessories cycle computer start?
- K
  Kevin BellAug 30, 2025
  When charging with the battery installed to a bicycle, you cannot turn the cycle computer ON. Stop charging. The power automatically turns OFF if charging is started while the cycle computer is running.
E
Evelyn HarrisAug 29, 2025
What to do if the key does not turn on my Shimano Steps Camera Accessories?
- C
  chadvillarrealAug 29, 2025
  If the key does not turn on your Shimano Steps Camera Accessories, foreign material such as dirt or dust may be stuck in the battery or battery mount. Turn the key while pushing the battery in the installation direction. If the battery is removed, follow the cleaning procedure to clean it.
M
Mrs. Felicia BakerAug 29, 2025
Why are my Shimano Steps Camera Accessories battery and charger getting so hot?
- L
  Larry SmithAug 29, 2025
  If the Shimano Steps Camera Accessories battery and battery charger become hot, the temperature of the battery and battery charger may exceed the operating temperature. Stop charging, and wait a while before starting to charge again.
C
Chad BarkerAug 28, 2025
Why doesn't the LED light up on my Shimano Steps Camera Accessories battery?
- K
  Kyle ThomasAug 28, 2025
  If the Shimano Steps Camera Accessories battery LED does not light up, it may be because the battery level has been at 0% for a long time, or the battery hasn't been charged after purchase. Charge the battery.
J
Jerry ReyesAug 27, 2025
How to fix Shimano Steps Camera Accessories when it cannot charge?
- R
  rothloganAug 27, 2025
  If your Shimano Steps Camera Accessories cannot charge, first, check the power plug of the battery charger. Remove and reconnect it securely, and then try charging again. Next, verify the charging plug of the battery charger is securely inserted into the battery by removing and reconnecting it. Also, check that the charging adapter and charging plug or charging adapter and battery charging port are securely connected. Finally, inspect the connection terminals of the battery charger, charging adapter, or battery for dirt. Clean them with a waste cloth or cotton bud dampened with ethanol, and then try charging again.

Shimano Steps BT-E6010 Specifications

General

Battery Type	Lithium-ion
Nominal Voltage	36 V
Nominal Capacity	11.6 Ah
Watt-hour Rating	418 Wh
Charging Time	5 hours
Compatibility	Shimano Steps E6000 series
Weight	2.55 kg
Operating Temperature	-10°C to 40°C
Compatible Charger	Shimano Steps EC-E6000