Why does my Shimano Steps SC-E6000 Bicycle Accessories battery quickly lose its charge?
If your Shimano Steps Bicycle Accessories battery quickly loses its charge, it may be at the end of its service life. In this case, replace the battery with a new one.
What to do if Shimano Steps Bicycle Accessories shows temperature protection warning?
To address a temperature protection issue with your Shimano Steps Bicycle Accessories battery, leave the battery in a cool place away from direct sunlight until its internal temperature decreases sufficiently. If the problem continues, contact the place of purchase.
What does E012 error mean on Shimano Steps Bicycle Accessories?
If you see error E012 on your Shimano Steps Bicycle Accessories, the initialization of the torque sensor failed. To resolve this, with your foot off the pedal, press the battery power button and turn on the power again. If the situation does not improve, contact the place of purchase.
What does W030 error mean on Shimano Steps SC-E6000 Bicycle Accessories?
If you encounter error W030 on your Shimano Steps Bicycle Accessories, it could be due to two or more assist switches connected to the system or a communication error between the drive unit and the motor unit. To resolve this: * Change the assist switch to the gear shifting switch, or connect only one assist switch and turn on the power again. * Check that the cable is properly connected between the drive unit and the motor unit. If the situation does not improve, contact the place of purchase.
How to fix E010 error on Shimano Steps Bicycle Accessories?
If you receive error E010 on your Shimano Steps Bicycle Accessories, it indicates a system error. Press the power button of the battery to turn it on again. If the problem persists, contact the place of purchase.
What does error E020 mean on Shimano Steps SC-E6000 Bicycle Accessories?
If you're getting error E020 on your Shimano Steps Bicycle Accessories, it means a communication error between the battery and drive unit was detected. To solve this, check that the cable between the drive unit and battery is properly connected. If the situation does not improve, contact the place of purchase.
Why does the LED on my Shimano Steps Bicycle Accessories charger not illuminate?
If the LED on your Shimano Steps Bicycle Accessories charger isn't lighting up, first, check the connection of the recharging plug to the battery for any foreign objects and reinsert it. Also, if the battery is fully charged, the LED may turn off, which isn't a malfunction. Disconnect and reconnect the charger's power plug to try again. If the LED still doesn't illuminate, contact the place of purchase.
Why is pedaling so stiff on my Shimano Steps SC-E6000?
If you find that pedaling feels stiff with your Shimano Steps Bicycle Accessories, here are a few things to check: * Ensure your tires are inflated to the correct pressure by using a pump to add air. * Verify that the assist mode is not set to [OFF]; set it to [HIGH]. * Check if the battery is running low and charge it fully. * Make sure you didn't turn on the power while your foot was on the pedal; try turning it on again without pressure on the pedal. If the issue continues after these checks, contact the place of purchase.
What to do if the Shimano Steps Bicycle Accessories battery cannot be recharged?
If your Shimano Steps Bicycle Accessories battery is not recharging, consider the following: 1. Ensure the charger's power plug is securely inserted into the electrical outlet; disconnect and reconnect to try again. 2. Make sure the charger's recharging plug is securely inserted into the battery; disconnect and reconnect to try again. 3. Verify the charging adapter is securely connected to both the charging plug and the battery charging port. 4. Check for dirt on the connecting terminals of the charger, adapter, or battery and clean with a dry cloth. If the battery still won't recharge after these steps, contact the place of purchase.
Why is assistance not being provided on my Shimano Steps SC-E6000 Bicycle Accessories?
If you're experiencing assistance issues with your Shimano Steps Bicycle Accessories, check these potential causes: * Ensure the battery is sufficiently charged and recharge if needed. * If riding on long slopes in summer or carrying heavy loads, turn off the power temporarily. * Assistance is not provided at speeds of 25 km/h or more, so check your speed. For issues related to incorrect connections or problems with the drive unit, cycle computer, or assist switch, contact the place of purchase.
Provides guidelines to ensure user safety when operating the system.
Provides detailed safety advice and warnings for battery handling and usage.
Lists detailed technical data including operating temperatures, battery type, and power ratings.
Provides essential safety warnings and procedures for charging the battery.
Provides guidelines for optimal battery charging and storage for longevity.
Step-by-step instructions for securely installing the battery into its mount.
Provides instructions on how to select different assist modes using the switches.
Guides on how to switch between automatic and manual gear shifting modes.
Lists common error indications shown by battery LED lamps and their remedies.
General| Display Type | LCD |
|---|---|
| Battery Level Indicator | Yes |
| Nominal Voltage | 36V |
| Maximum Power Output | 250W |
| Assist Modes | Eco |
| Position | Handlebar |
| Mounting | Handlebar |
| Functions | Speed, distance, battery level |
| Compatibility | Shimano STEPS system |
To Next Page
