Shini SHD-EB User Manual

49 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

SHD-EB

Budget Hopper Dryer

Date: Mar, 2017

Version: Ver.A

Table of Contents

Questions and Answers:

S
Samantha GloverAug 17, 2025
Why is the blower running, but the heater temperature is not high enough in my Shini Dryer?
- A
  Angela WalkerAug 17, 2025
  Several factors can cause this issue: * The pipe heater or lead sheet may be defective, requiring you to check and replace them. * The temperature protector may be broken or tripped; inspect and reset if necessary. * A solenoid switch phase shortage could be the culprit; check and replace it. * The temperature controller might be broken or have a large error; consider replacing it.
P
Patrick MooreAug 20, 2025
What to do if the blower is running but the heater is overheating in Shini Dryer?
- C
  Christine Carlson DVMAug 20, 2025
  If the blower is running, but the heater is overheating, consider these potential causes: * A blocked pipe heater. Clean it up. * A faulty temperature controller. Replace the temperature controller or adjust the fine-tune button. * A solenoid switch contact bonding. Replace it.
S
Stephen MendozaAug 22, 2025
What to do if the blower doesn’t work and has smoke in Shini SHD-EB Dryer?
- M
  Mrs. Janice VegaAug 22, 2025
  If the blower doesn’t work and has smoke, it could be due to: * A blower fault. Check and replace the blower. * An open solenoid switch contact. Check, repair, or replace the solenoid switch.
K
Katherine RobertsAug 26, 2025
Why is the blower running, but the heater isn’t heating in my Shini SHD-EB Dryer?
- M
  Matthew CastroAug 26, 2025
  If the blower runs, but the heater doesn’t heat, check the following: * A burnt pipe heater connecting lead sheet. Check and replace it. * A faulty solenoid switch. Check, replace, or repair it. * A pipe heater fault. Check and replace it. * A temperature fault without output. Replace the temperature controller. * A thermocouple fault. Replace the thermocouple.
E
Elizabeth ChangAug 27, 2025
How to fix the blower running in the opposite direction in Shini SHD-EB?
- N
  nandersonAug 27, 2025
  If the blower is running in the opposite direction, it is likely due to a blower reverse connection. To resolve this, replace any two blower power cables.
J
Justin GoodmanAug 30, 2025
What to do if the blower doesn’t running and heater doesn’t work in Shini SHD-EB?
- J
  jrobinsonAug 30, 2025
  If the blower and heater are not working, check these possible causes: * Overload relay trips. Check and replace the overload relay. * Transformer fault. Check and replace the transformer. * Fuse burnt. Check and replace the fuse. * Power fault. Check if there’s a phase shortage.
E
edwardjohnsonSep 2, 2025
Why is the temperature too high when the blower runs on my Shini Dryer?
- A
  Arthur ConnerSep 2, 2025
  If the Shini Dryer's blower runs but the temperature is too high, it could be due to a jam in the hot-air pipe, requiring cleaning. Alternatively, the temperature controller may be faulty or have a significant error, in which case you should replace the temperature controller or adjust the inching switch. Another potential cause is that the electromagnetic switch contacts are stuck; if this is the case, replace the switch.
A
Amanda Conrad MDSep 4, 2025
What to do if the blower can run but temperature is too low in my Shini Dryer?
- T
  Terri YorkSep 4, 2025
  If your Shini Dryer's blower is running but the temperature is too low, the plumb slip of the heater pipe might be faulty, requiring a check and change. Another cause may be that the EGO jumped or is breaking, so check or reset it. Also, the magnetic switch might lack a phase, so check and change it. Finally, the temperature controller could be damaged or have too much error, so you should change the temperature controller.
J
jamesdukeSep 7, 2025
Why is there no temperature for blower running in my Shini Dryer?
- S
  Stephen BensonSep 7, 2025
  If there is no temperature when the blower is running on your Shini Dryer, it could be due to several reasons. The plumb slip of the heater pipe might have melted, requiring a check and change. Alternatively, the magnetic switch or the heater pipe itself could be faulty, also requiring a check and change. A power supply fault, such as a lack of phase, could be the cause, so check the power supply. Finally, the thermocouple might be faulty, in which case it should be changed.
P
phelpsdavidSep 9, 2025
What to do if the blower is not rotating and not heating in my Shini Dryer?
- A
  Allison ReedSep 9, 2025
  If the blower in your Shini Dryer is not rotating and not heating, it could be due to several issues. The overload might have jumped, requiring a check and change. Alternatively, the transformer or the fuse might be faulty or melted, also requiring a check and change. Another potential cause is a power supply fault, so check for a lack of phase.

Shini SHD-EB Specifications

General

Brand	Shini
Model	SHD-EB
Category	Dryer
Language	English

Related product manuals

Preview: Shini SHD-EB Series

Shini SHD-EB Series