Steam en
17
‒ When the food is ready, press
to switch the
appliance off.
10.
Empty the water tank and dry the cooking compart-
ment.
→"After every steam operation", Page17
Changing the type of heating
When you change the type of heating, the other set-
tings are also reset.
1.
Press
to pause operation.
2.
Press the type of heating.
3.
Turn the rotary selector to select the required type
of heating.
a The corresponding recommended temperature ap-
pears on the display.
Changing the cooking time
You can change the cooking time at any time.
▶
Use the rotary selector to change the cooking time.
a The change is applied immediately.
Changing the temperature
You can change the temperature at any time.
1.
Press the temperature.
2.
Use the rotary selector to change the temperature.
a The change is applied immediately.
11.3 Steam assistance
When you cook with steam assistance, the appliance
introduces steam into the cooking compartment at vari-
ous intervals. This gives your food a crispy crust and a
shiny surface. Meat stays juicy, tender and only under-
goes a minimum reduction in volume.
Suitable types of heating with steam-assisted
cooking
Only certain types of heating are suitable for operation
with steam-assisted cooking.
You can switch on steam assistance for the following
types of heating:
¡ 4Dhot air
¡ Top/bottom heating
¡ Circulated air grilling
¡ Keeping warm
Setting steam-assisted cooking
Requirement:The water tank has been filled.
→"Filling the water tank", Page16
1.
Press .
2.
In the operating modes menu, set the "Types of
heating".
3.
Use the rotary selector to set the type of heating.
4.
Press the temperature.
5.
Use the rotary selector to set the temperature.
6.
Press the steam injection.
7.
Use the rotary selector to set the steam injection.
Steam injection
Low
Medium
Heavy
8.
Press
to start the operation.
Note:If the water tank runs dry during operation, a
notification appears in the display. The appliance
continues to operate without steam injection.
→"Filling the water tank", Page16
a The appliance starts heating.
a The time, the operation duration and the settings are
shown in the display.
9.
When the food is ready, press
to switch the
appliance off.
10.
Empty the water tank and dry the cooking compart-
ment.
→"After every steam operation", Page17
Changing the type of heating
When you change the type of heating, the other set-
tings are also reset.
1.
Press
to pause operation.
2.
Press the type of heating.
3.
Turn the rotary selector to select the required type
of heating.
a The corresponding recommended temperature ap-
pears on the display.
Changing the temperature
You can change the temperature at any time.
▶
Use the rotary selector to change the temperature.
a The change is applied immediately.
Changing the steam setting
You can change the steam setting at any time.
1.
Press the steam setting.
2.
Use the rotary selector to change the steam setting.
a The change is applied immediately.
11.4 After every steam operation
The remaining water is pumped back into the water
tank after every operation with steam. Then empty and
dry the water tank and the cooking compartment.
Emptying the water tank
WARNING‒Risk of burns!
The water tank may heat up while the appliance is in
operation.
▶ Wait until the water tank has cooled down from the
previous operation.
▶ Remove the water tank from the tank recess.
ATTENTION!
Drying the water tank in the hot cooking compartment
leads to damage to the water tank.
▶ Do not dry the water tank in the hot cooking com-
partment.
Cleaning the water tank in the dishwasher will damage
it.
▶ Do not clean the water tank in the dishwasher.
▶ Clean the water tank with a soft cloth and standard
washing-up liquid.
Note:Once the appliance has been switched off, the
button remains lit for a little longer to remind you to
empty the water tank.
1.
Use
to open the control panel.
2.
Remove the water tank.
3.
Carefully remove the lid of the water tank.
To Next Page
Loading...
