Siemens SINAMICS G120C - Page 52

Commissioning
4.2 Commissioning with BOP-2 operator panel
SINAMICS G120C converter
52 Getting Started, 04/2014, FW V4.7, A5E34264105B AA
r2053
PROFIdrive diagnostics send PZD word
[0]
PZD 1
…
[7]
PZD 8
r2054
PROFIBUS status
0
Off
1
No connection (search for baud rate)
2
Connection OK (baud rate found)
3 Cyclic connection with master (data
exchange)
4
Cyclic data OK
r2055
PROFIBUS diagnosis standard
[0]
Master bus address
[1]
Master input total length bytes
[2]
Master output total length bytes
r2057
PROFIBUS address switch diagnostics
r2060
CO: IF1 PROFIdrive PZD receive double word
[0]
PZD 1 + 2
…
[10]
PZD 11 + 12
r2061 CI: IF1 PROFIdrive PZD send double word
[0]
PZD 1 + 2
…
[10]
PZD 11 + 12
r2063 IF1 PROFIdrive diagnostics PZD send double
word
[0]
PZD 1 + 2
…
[10]
PZD 11 + 12
r2067
IF1 PZD maximum interconnected
[0]
Receiving
[1]
Sending
p2072
Response, receive value after PZD failure
.00 Unconditionally open
holding brake (p0855)
1 = freeze value
0 = zero value
r2074
PROFIdrive diagnostics bus address PZD receive
[0]
PZD 1
…
[7]
PZD 8
r2075 PROFIdrive diagnostics telegram offset PZD
receive
[0]
PZD 1
…
[7]
PZD 8
r2076
PROFIdrive diagnostics telegram offset PZD send
[0]
PZD 1
…
[7]
PZD 8
r2077 PROFIBUS diagnostics peer-to-peer data transfer
addresses
p2079
PROFIdrive PZD telegram selection extended
See p0922
p2080
BI: Binector-connector converter, status word 1
The individual bits are combined to form status
word 1.
p2088
Binector-connector converter, invert status word
r2089 CO: Send binector-connector converter status
word
[0]
Status word 1
[1]
Status word 2
[2]
Free status word 3
[3]
Free status word 4
[4]
Free status word 5
r2090
BO: PROFIdrive PZD1 receive bit-serial
r2091
BO: PROFIdrive PZD2 receive bit-serial
r2092
BO: PROFIdrive PZD3 receive bit-serial
r2093
BO: PROFIdrive PZD4 receive bit-serial
r2094
BO: Connector-binector converter binector output
r2095
BO: Connector-binector converter binector output
p2098 Invert connector-binector converter binector
output
p2099
CI: Connector-binector converter signal source
p2100
Setting the fault number for fault response
p2101
Setting the fault response
0
None
1
OFF1
2
OFF2
3
OFF3
5
STOP2
6
DC braking
p2103
BI: 1. Acknowledge faults
p2104
BI: 2. Acknowledge faults
p2106
BI: External fault 1
r2110
Alarm number
p2111
Alarm counter
p2112
BI: External alarm 1
r2122
Alarm code
r2123
Alarm time received [ms]
r2124
Alarm value
r2125 Alarm time removed [ms]
p2126
Setting fault number for acknowledge mode
p2127 Sets acknowledgement mode
p2128
Selecting fault/alarm code for trigger
r2129
CO/BO: Trigger word for faults and alarms
r2130
Fault time received in days
r2131
CO: Actual fault code
r2132
CO: Actual alarm code
r2133
Fault value for float values
r2134
Alarm value for float values
r2135
CO/BO: Status word, faults/alarms 2
r2136
Fault time removed in days