Siemens SINEC L2

Programmer Functions Over the SINEC L2 Network S5-95U, SINEC L2
Press <F4> (ACTIVATE) in the "FUNCTION SELECTION/DEFAULTS"
screen.
The edited path appears on the monitor.
Figure 9-6. Screen for Activating a Path (1)
F2 F5
TOTAL
a a a a a a a a a a a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a a a a a a a a a a a
F7
a a a a a a a a a a a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a a a a a a a a a a a
F8
EXIT
F1
SYSID
F4F3
SUBPATH
a a a a a a a a a a a a a
a
a a a a a a a a a a a
a
a
a a a a a a a a a a a
a
a
a a a a a a a a a a a
a
a
a a a a a a a a a a a
a
a a a a a a a a a a a a a
a a a a a a a a a a a a a
a
a a a a a a a a a a a
a
a
a a a a a a a a a a a
a
a
a a a a a a a a a a a
a
a
a a a a a a a a a a a
a
a a a a a a a a a a a a a
a a a a a a a a a a a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a a a a a a a a a a a
a a a a a a a a a a a a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a a a a a a a a a a a a
a a a a a a a a a a a a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a a a a a a a a a a a a
a a a a a a a a a a a a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a a a a a a a a a a a a
F6
a a a a a a a a a a a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a
a a a a a a a a a
a
a a a a a a a a a a a
a a a a a a a a a a a a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a
PATH NAME : ST2/95U
SINEC L2
a a a a a a a a a a a a a a
a
a a a a a a a a a a a a
a
a
a a a a a a a a a a a a
a
a a a a a a a a a a a a a a
PG/CP-L2
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
CP-L2 ADDRESS : 2
a a a a a a a a a a a a a a
a
a a a a a a a a a a a a
a
a
a a a a a a a a a a a a
a
a a a a a a a a a a a a a a
ENDP
Activate the first path level by pressing <F3> (SUBPATH).
The activated subpath is then marked with an "* ", and "DIRECT PG LINK ESTABLISHED" appears
in the message bar.
Press <F1> (SYSID) to match the local LAN parameters of the CP-L2 communications
processor in the programmer to the L2 LAN parameters (basic L2 parameters) of the system
( section 9.5).
9-8 EWA 4NEB 812 6112-02