EasyManua.ls Logo

SIGLENT SDS1072CML - User Manual

SIGLENT SDS1072CML
140 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
I
User Manual
Digital Storage Oscilloscope
Version No.: V 1.6

Table of Contents

Other manuals for SIGLENT SDS1072CML

Preview: Service Manual
Service Manual61 pages

Questions and Answers

  • N
    nicholsonryanAug 5, 2025
    What to do if the SIGLENT Test Equipment screen remains dark after power on?
    • M
      Matthew RiveraAug 5, 2025
      If the screen of your SIGLENT Test Equipment stays dark after you turn it on: * Ensure the power cord is properly connected. * Inspect the fuse for burnout. If a replacement is needed, contact SIGLENT to return the instrument for repair by authorized personnel. * Restart the instrument after checking the connections and fuse. * If the issue persists, further troubleshooting or contacting SIGLENT may be required.
  • B
    bonddanielAug 9, 2025
    Why is the waveform displaying on my SIGLENT Test Equipment not stable?
    • W
      wolfemarkAug 9, 2025
      If the waveform display on your SIGLENT Test Equipment is unstable, consider the following: * Check the trigger source to ensure the “Source” in the “TRIG” menu matches the actual operating channel. * Verify the waveform itself, ensuring the time base is appropriate for the input signal's frequency. * Confirm the trigger type is correct; “Edge” is suitable for general signals, while “Video” is best for video signals. * Adjust the trigger holdoff setting.
  • G
    garrettkimAug 13, 2025
    How to fix no waveform displaying on SIGLENT Test Equipment after sampling the signal?
    • A
      Amanda AndersonAug 13, 2025
      If you're not seeing a waveform on your SIGLENT Test Equipment after sampling a signal: * Ensure the signal cord is correctly connected to the BNC connector. * Verify the Intensity knob on the front panel is properly adjusted. * Confirm the probe is correctly connected to the device under test. * Check if the device under test is generating a signal. You can use the probe compensation signal to test the channel. * Try resampling the signal.
  • B
    Benjamin MiddletonAug 18, 2025
    Why is the voltage amplitude measured on my SIGLENT Test Equipment inaccurate?
    • D
      Daniel ThomasAug 18, 2025
      If the voltage amplitude measured by your SIGLENT Test Equipment is inaccurate: * Verify that the attenuation coefficient of the channel matches the probe's attenuation ratio. * Check if the BW Limit is enabled under the CH1/CH2 menu. If it's on, it can cause the amplitude to appear lower than the actual value.
  • M
    Michael Velasquez Jr.Aug 21, 2025
    What to do if there is no display after pressing RUN/STOP on SIGLENT Test Equipment?
    • J
      Jessica GarciaAug 21, 2025
      If nothing displays after pressing RUN/STOP on your SIGLENT Test Equipment: * Check if the trigger Mode is set to “Normal” or “Single” and if the trigger level is outside the waveform range. Adjust the trigger level to the middle or change the trigger Mode to “Auto”. * Alternatively, press AUTO to automatically adjust these settings.
  • L
    lopezelijahAug 27, 2025
    Why my SIGLENT Test Equipment does not recognize the U disk?
    • J
      Jessica SmithAug 27, 2025
      If your SIGLENT Test Equipment isn't recognizing the U disk: * Confirm the U disk works normally. * Check if the USB Device interface is functioning correctly. * Ensure you're using a flash-type U disk, as hardware types are not supported. * Make sure the U disk's capacity isn't too large; a capacity no larger than 4 GB is recommended. * Restart the instrument and re-insert the U disk. * If problems persist, contact SIGLENT.
  • W
    Wendy GoodwinAug 30, 2025
    How to resolve ladder-like waveform display on SIGLENT Test Equipment?
    • J
      Jody JohnsonAug 30, 2025
      If the waveform on your SIGLENT Test Equipment looks like a ladder: * Increase the horizontal time base to improve the horizontal resolution for better waveform display. * If the “Type” in the “DISPLAY” menu is set to “Vectors”, switch it to “Dots”.

Summary

General Safety Summary

To Avoid Fire or Personal Injury

Safety precautions to avoid injury and prevent damage, use only as specified.

Chapter 1 Accidence

Front Panel and User Interface

Function Checking Procedure

Chapter 2 Functions Instruction and Operation

Menu and Control Buttons

Description of the oscilloscope's menu system and control buttons for operation.

Input and Output Connectors

Auto Setup Function

How the auto setup function identifies waveforms and adjusts controls for a usable display.

Universal Knob Operation

Vertical System Controls

Explanation of vertical controls for waveform display, scale, and position.

Horizontal System Controls

Functions and knobs for controlling horizontal scale and position of waveforms.

Trigger System Configuration

How to set up triggers to acquire and display meaningful waveforms stably.

Acquiring Signals System

Display System Settings

Measurement System

Tools for scale, cursor, and automatic measurements of waveforms.

Storage System Functions

Self Calibration Procedure

Procedure to optimize the signal path for maximum measurement precision.

Self Test Routine

Chapter 3 Application Examples

Simple Measurements

Cursor Measurements

Analyzing Signal Detail

Differential Communication Signal Analysis

Chapter 4 Prompting Messages and Troubleshooting

Troubleshooting Common Issues

Guidance for resolving common problems like dark screen, no signal, or unsteady display.

Appendix A: Specifications

Appendix B: Default Setup

SIGLENT SDS1072CML Specifications

General IconGeneral
BrandSIGLENT
ModelSDS1072CML
CategoryTest Equipment
LanguageEnglish

Related product manuals