SIGLENT SDS1202X - Page 2

188 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

www.biall.com.pl

Table of Contents

Safety Information4
- General Safety Summary4
- Safety Terms and Symbols6
- Measurement Category7
- Working Environment8
- Ventilation Requirement9
- General Care and Cleaning10
Document Overview11
Table of Contents13
Quick Start21
- General Inspection22
- Appearance and Dimensions23
- To Prepare the Oscilloscope for Use24
- Front Panel Function Overview32
- Help38
- User Interface39
- To Use the Security Lock41
To Set the Vertical System42
- To Enable the Channel43
- To Adjust the Vertical Scale44
- To Adjust the Vertical Position44
- To Specify Channel Coupling45
- To Specify Bandwidth Limit45
- To Specify Probe Attenuation Factor46
- To Specify Channel Input Impedance46
- To Specify Amplitude Unit47
- To Invert a Waveform47
Set the Horizontal System48
- Adjust the Horizontal Scale49
- Adjust Trigger Delay50
- Set the Roll Mode51
- Use the Zoom Function52
To Set the Sample System53
- Run Control54
- Overview of Sampling55
- Select Memory Depth58
- Select Sampling Mode59
- Select Waveform Interpolation Method60
- Figure 12 X Interpolation61
- Select Acquisition Mode62
- Change the Horizontal Format66
- Use Sequence Mode67
To Trigger the Oscilloscope69
- Trigger Source71
- Trigger Mode72
- Trigger Level73
- Trigger Coupling74
- Trigger Holdoff75
- Noise Rejection76
- Figure 22 Turn on the Noise Reject77
- Trigger Type78
Serial Trigger and Decode98
- IIC Trigger and Serial Decode99
- SPI Triggering and Serial Decode105
- UART/RS232 Triggering and Serial Decode112
To Save Reference Waveform116
- To Save REF Waveform to Internal Memory117
- To Display REF Waveform117
- To Adjust REF Waveform Display118
- To Clear REF Waveform Display118
To Make Math Operation119
- Units for Math Waveforms119
- Math Operators120
- Math Function Operation125
To Make Cursors Measurements128
- Cursors128
- Y Cursors128
- To Make Cursor Measurements129
To Make Measurements130
- Type of Measurement131
- To Make Automatic Measurement135
- Figure 65 Added the Measurement136
- To Clear Measurement Parameters137
- To Make All Measurement137
Display Setting138
- To Set Display Type139
- To Set Color Display140
- To Set and Clear Persistence140
- To Clear the Display141
- To Select Grid Type142
- To Adjust Waveform Intensity142
- Figure 71 Intensity Set to 100143
- To Adjust Grid Brightness144
- To Adjust Transparence144
Save and Recall145
- Save Type146
- Internal Save and Recall147
- External Save and Recall148
- Figure 74 Select Save Location149
- Disk Management151
System Function Setting154
- To View the System Status155
- To Do Self Calibration156
- To Enable or Disable the Sound157
- To Specify the Language157
- To Do Pass/Fail Test158
  - To Set and Perform Pass/Fail Test159
  - To Save and Recall Test Mask160
- IO Set162
- To Enable Quick-Cal165
- To Update Firmware and Configuration166
- Do Self Test167
  - Keyboard Test168
  - LED Test169
- To Specify Screen Saver Time170
- Option Management171
- Figure 87 Option Information172
To Use the History Function173
Arbitrary Waveform Generator175
- To Set Wave Type and Parameters176
- To Output Arbitrary Waveform178
- To Set Output Load179
- Recover the Default Values of Wave Gen179
- AWG Self Cal180
Default Setup181
Troubleshooting187

Other manuals for SIGLENT SDS1202X

Quick Start Guide13 pages

Related product manuals

SIGLENT SDS1202X-E

Preview: SIGLENT SDS1202X-U Series

SIGLENT SDS1202X-U Series

SIGLENT SDS1204X-E

Preview: SIGLENT SDS1204X HD

SIGLENT SDS1204X HD

Preview: SIGLENT SDS1102X

SIGLENT SDS1102X

Preview: SIGLENT SDS1022DL

SIGLENT SDS1022DL

SIGLENT SDS1052DL

SIGLENT SDS1104X-E

SIGLENT SDS1102CML

Preview: SIGLENT SDS1072CML

SIGLENT SDS1072CML

Preview: SIGLENT SDS1000X+ Series

SIGLENT SDS1000X+ Series

Preview: SIGLENT SDS1000X-E Series

SIGLENT SDS1000X-E Series