6 S4100-0034-12 3/2012
Amplifier and Related Audio Options (Continued)
Model Description Details and Mounting Reference
4100-5116
Expansion Signal Module; three, 1.5 A Class B
NACs; up to five maximum per amplifier; NAC
rating = 1.5 A, 50 W, or 100 speakers maximum
Converts one NAC input to three NAC outputs; selects between two inputs;
for Flex-35/50 amplifiers only, two input NACs are required; Single Block
module mounts in expansion bay; Supv. = 20 mA; Alarm = 80 mA
4100-1266
Expansion Signal Module NAC Expander; NAC
rating = 1.5 A, 50 W, or 100 speakers maximum
Expands module capacity to six, Class B NACs;
Supv. = 0.84 mA; Alarm = 60 mA
These modules
mount on the
4100-5116;
select one max.
per 4100-5116
as required
4100-1267
Expansion Signal Module Class A Adapter; NAC
rating = 1.5 A, 50 W, or 100 speakers maximum
Converts 3 Class B, NACs to Class A; Supv. = 1 mA;
Alarm = 30 mA
4100-1268
Expansion Signal Module Constant Supervision
Adapter for 25 VRMS or 70.7 VRMS; NAC rating
= 1.4 A, 50 W, or 100 speakers maximum
Converts 3 Class B NACs to Class B or Class A Constant
Supervision NACs; Supv. = 38 mA on batteries (constant
supervision deactivated); Alarm = 70 mA
4081-9018 End-of-line resistor harness for 70.7 VRMS NACs; 10 k
, 1 W
4100-2300 Expansion Bay Hardware; order one for each expansion bay
4100-2320 Audio Bay-to-Bay Interconnection Harness Kit; order one for each audio bay addition
4100-0637 Audio Box Interconnection Harness Kit; order one for each close-nippled audio cabinet
Audio Input and Controller Options (see page 2 for custom message ordering)
Model Description Details and Mounting Reference
4100-1240
Auxiliary Audio Input Module; four additional
(unsupervised) inputs per module; 2 maximum
Inputs for 10 VRMS, 25 VRMS, 70.7 VRMS, line level (0.707 VRMS), or
microphone; 1 Block; current = 10 mA
4100-1241 8 Minute Message Expansion Module
Provides 8 minutes at normal resolution or 4 minutes at high
resolution, Supv. = 2 mA; Active = 17 mA
Mounts to
audio
controller
module
4100-1242 32 Minute Message Expansion Module
Provides 32 minutes at normal resolution or 16 minutes at
high resolution; Supv. = 2 mA; Active = 17 mA
Operator Interface and Related Options
Model Description Details and Mounting Reference
4100-1243
Microphone Module (mike); for Fire Alarm
Control Panels
One maximum per audio system; front panel module that
requires 2 Slots (4”), locate on expansion bay only; space
behind for 4100ES flat modules only
Supervisory
current =
2.4 mA
Active
current =
6 mA
4100-1244
Remote Microphone Module; for Remote
Annunciator Panels
Front panel module that requires 2 Slots (4”), locate on
expansion bay only; space behind for 4100ES flat modules
only; distance limited to 4000 ft (1219 m)
4100-1252 1 Channel (audio or mike)
Operator
Interface
LED/Switch
Modules
Single Slot LED/switch modules; connects to a 4100-1288 or 4100-1289
LED/switch controller in the same bay; space behind controller accepts
4100ES flat modules only (see drawings on p. 4); current = 24 mA;
Additional adjacent LED/switch modules, as shown on p. 4, are used as
required for specific speaker circuit selection (refer to data sheet
S4100-0032 for LED/switch module availability)
4100-1253 1.5 Channel (audio + mike)
4100-1254 2 Channel (full audio)
4100-1255
3-8 Channel (8 channel normal
res. messages, 4 channels of high
res. messages)
4100-1288
64 LED/64 Switch Controller
Module with mounting plate
Refer to
data sheet
S4100-0032
for details
Mounts behind the LED/switch modules; has
provisions for one 4100-1289 Controller Module
LED/switch controllers
and their connected
modules must be in
the same bay
4100-1289
64 LED/64 Switch Controller
Module without mounting plate
Mounts on extra space of 4100-1288; controls
additional 64 LEDs and 64 switches
Firefighter Telephone System Products
Model Description Details and Mounting Reference
4100-1270
Master Telephone with Control Module and
three Class B telephone NACs, one maximum
per audio system; for use in Fire Alarm Control
Panels only; includes one 4100-1272 Module
Front panel module; space behind for 4100ES flat modules only; phone
control module included, mounted on bay module mounting plate; for
individual telephone circuit control, use LED/switch modules;
Supv. = 80 mA; in use = 140 mA + remote phones (see table on page 7)
4100-1271 Remote Master Telephone Mounts in Remote Annunciator Panel only (see S4100-0038)
4100-1272
Expansion Telephone Control Module with three
Class B telephone NACs
Expansion module for additional telephone circuits in main control or
transponders; Supv. = 80 mA; in use = 140 mA + remote phones
4100-1273 Telephone NAC Class A Adapter Module Mounts to 4100-1270 or -1272; no additional current required
Network and MINIPLEX Transponder Audio Connection Options
Model Description Details
4100-0623
Network Audio Riser Controller Module for
control of either an analog or digital riser module
Typically for Network nodes without an audio controller, used for NAA
applications; mounts in Block A; current = 35 mA
4100-0621
Dual Channel Analog Audio Riser
Module
Select one,
mounts in
Block B
Accepts two separate audio signals from host; controlled by Transponder
Interface Module; current = 25 mA when active
4100-0622
3-8 Channel Digital Audio Riser
Module; with NAA input
Receives and decodes digital inputs; up to eight audio channels;
current = 70 mA; NAA input for 25, 70.7, or 0.707 VRMS
4100-1341
MCC (Multiple Command Center)
Digital Audio Riser Interface
Selects a single digital audio channel and converts it to an analog line level
for input to an analog 4100ES/ 4100U/4100 Legacy voice panel; current =
70 mA
4100-9854 4100/4100+ Legacy bay mounting kit Use to mount 4100-1341 MCC Digital Audio Riser Interface in legacy panel
4100-1258
NPU to 4100ES Audio Interconnect Module;
mounts in 4100ES Audio cabinet
Dual terminal block module with harnesses for connecting to the Audio
Controller and Telephone Control module (requires 1 Block)
Emergency Voice/Alarm Communications Equipment Product Selection (Continued)
To Next Page
Loading...
Need help?
General
