Simplicity 1692143 User Manual

How to use this file...(Labels & Miscellaneous Documents)
————————————————————————————————————————————–––
Instructions for
Print Vendors (Paper Manuals)
Paper: * Various...
Press: * Various...
Bindery: * Various...
General: * This instruction page is NOT part of the document and must NOT be printed.
• Pages labeled with the text “THIS PAGE INTENTIONALLY BLANK” are placement pages ONLY,
and should NOT be printed.
• THIS document will most likely be a unique piece -- either a label or certificate or
other such miscellaneous format.
• EXACT specifications on the print & job specs should already be known to
you. In you are uncertain of what these specifications are, please contact
Simplicity Technical Publications.
• (Note: We will do our best to answer your questions concerning this job, but may need to transfer
you to another department within our company for additional specifications and job
requirements).
————————————————————————————————————————————–––
If you have further questions on how to utilize this file, please contact
Simplicity Technical Publications Department at (262) 284-8647.

Simplicity 1692143 Specifications

General

Type	Lawn Tractor
Fuel	Gasoline
Drive	2WD
Transmission	Hydrostatic
Weight	450 lbs
Engine	Briggs & Stratton
Engine Type	Single Cylinder
Fuel Tank Capacity	2.5 gal
Turning Radius	18 in
Tire Size - Front	15x6-6
Tire Size - Rear	20x8-8

Summary

Commercial Front-Cut Rider with Eaton Model 7 Hydrostatic

Neutral Position Adjustment

Ensuring the transmission control linkage is set for exact neutral position.

Spring-Centered Lever Adjustment

Adjusting levers to automatically return to neutral when released.

Forward Travel Stop Adjustment

Limiting maximum hydro pump output speed for straight forward travel.

Reverse Travel Stop Adjustment

Controlling maximum reverse speed by adjusting set collar position.

Large-Frame Tractors with Shaft Drive - Sundstrand Model 15 Hydrostatic

Section 2 Neutral Adjustment

Procedure to adjust transmission to prevent tractor creep when lever is in neutral.

Large-Frame Tractors with Belt Driven - Sundstrand Model 15 Hydrostatic

Section 3 Neutral Adjustment

Adjusting hydrostatic control lever to prevent tractor creep in neutral position.

Tractors with Tuff Torq K215-A & HydroGear BDU-21L

Section 4 Early Model Neutral Adjustment

Procedure for adjusting neutral on early models of BDU-21L hydrostatic transmission.

Section 4 Late Model Kit Neutral Adjustment

Neutral adjustment for late models with specific kit installed.

Section 4 Mid-Procedure Neutral Adjustment

Adjusting shift lever to prevent forward/reverse movement in neutral gate.

Section 4 Hydro Return-to-Neutral Adjustment

Ensuring shift lever returns to neutral when clutch/brake pedal is depressed.

Tractors with Eaton 850 Transaxle

Section 5 Neutral Adjustment

Adjusting tractor neutral position, including quadrant and linkage adjustments.

Tractors with Tuff Torq K60 Hydrostatic Transaxle

Section 6 K60 Neutral Adjustment

Section 6 K60 Neutral Adjustment (Continued)

Section 6 K60 Return-to-Neutral Adjustment

Lawn Tractors with Eaton 750 or 751 Transaxles

Section 6 Eaton 750 Welded Bracket Neutral Adjustment

Section 6 Eaton 750 Plastic Bracket Neutral Adjustment

Lawn Tractors with Eaton 750 Hydrostatic Transaxle

Section 6 Eaton 750 Neutral Adjustment

Section 6 Eaton 750 Return-To-Neutral

Lawn Tractors with Eaton 751 Hydrostatic Transaxle

Section 6 Eaton 751 Neutral Adjustment

Lawn Tractors with HydroGear BDU10S Transaxle

Section 7 BDU10S Two Ball Joint Neutral Adjustment

Section 7 BDU10S One Ball Joint Neutral Adjustment

Lawn Tractors with HydroGear 310-0500 Transaxle (Hand Control)

Section 7 HydroGear 310-0500 Neutral Adjustment

Section 7 HydroGear 310-0500 Return-to-Neutral Adjustment

Lawn Tractors with HydroGear 318-0500/322-0500/322-0650 Transaxle (Foot Control)

Section 7 HydroGear 318-0650 Neutral Adjustment

Lawn Tractors with Eaton Model 7 & Peerless 1300 Series Transaxle

Section 8 Eaton Model 7 Neutral Adjustment

Later Model Front-Cut Rider with Eaton Model 7 Hydrostatic

Section 9 Later Model Neutral Adjustment

Early Model Front-Cut Rider with Eaton Model 7 Hydrostatic

Section 10 Early Model Neutral Adjustment

Mid-Engine Riding Mowers with HydroGear 311-0500

Section 11 Mid-Engine Neutral Adjustment

Section 11 Mid-Engine Return to Neutral Adjustment