Need help?Do you have a question about the Simrad AC42 and is the answer not in the manual?
General| Type | Autopilot System |
|---|---|
| Power Supply | 12/24V DC |
| Operating Temperature | -15°C to +55°C |
| Water Resistance | IPX6 |
| Maximum Drive Output Current | 10A |
| Compass Heading Resolution | 0.1° |
| Humidity | 95% non-condensing |
| Storage Temperature | -25°C to +70°C |
| Compatibility | NMEA 2000 |
| Certification | CE |
Explains the manual's intent and highlights emphasized text for reader attention.
Overview of the autopilot computer as the main unit in AP24/AP28 systems.
Guidance on reading the manual and understanding system components.
Information on checking serial numbers and software versions for control units and computers.
Step-by-step guide for autopilot system installation.
Instructions for carefully unpacking and inspecting autopilot system components.
Guidance on understanding system configuration before installation.
Diagram illustrating the AP24 basic system layout and component connections.
Details on mounting the autopilot computer unit vertically and avoiding water exposure.
Recommendations for using shielded cables and proper wire gauge for motor supply.
Table providing recommended cable sizes based on voltage and length for drive units.
Explains AC12/AC42 board terminals, polarity protection, and RFI considerations.
Mounting and mechanical linkage instructions for RF300 and RF25 rudder feedback units.
Detailed guide on rudder feedback unit alignment and linkage for optimal performance.
Information on installing the LF3000 waterproof feedback unit with specific mounting brackets.
Step-by-step instructions for mounting the LF3000 linear feedback unit to the drive unit cylinder.
Information on drive units, voltage, and performance tables for hydraulic pumps.
Details on linear drive units and connecting reversible pumps to the autopilot computer.
Avoid mounting control units in direct sunlight or where moisture is present.
Instructions for panel mounting and optional bracket mounting of the AP24 control unit.
Details for panel and bracket mounting of the AP28 control unit.
Guidelines for mounting the FC40 and RC42 compass sensors for accurate heading data.
Mounting instructions for the R3000X remote control and JS10 joystick.
Instructions for installing the S35 NFU Lever and system interfacing options.
Details on SimNet cable system, connectors, and network setup.
Rules for SimNet power connection and network termination to prevent interference.
Illustrates small and medium SimNet network configurations and connections.
Diagram illustrating an expanded SimNet network configuration and connections.
Diagram and specifications for connecting an external alarm relay or buzzer.
Lists part numbers for AP24/AP28 control units and their mounting kit accessories.
Lists part numbers for AC12/AC42 autopilot computers and related accessories.
Lists spare parts for FC40, RC42 compasses and RF300, RF25 rudder feedback units.
Catalog of SimNet cables, joiners, and accessories for network expansion and connection.
Overview of autopilot system capabilities, boat types, and network specifications.
Details on steering modes, turn modes, and instrument data interface (PGNs).
Specifies SimNet/NMEA2000 PGNs for various instrument data points.
Detailed specifications including dimensions, weight, power, and environmental protection for AP24.
Detailed specifications including dimensions, weight, power, and environmental protection for AP28.
Technical data for AC12/AC42 autopilot computers, including drive capabilities and inputs.
Diagrams showing AC12/AC42 dimensions and cable retainer specifications.
Technical details for the FC40 compass, including performance and environmental ratings.
Technical details for the RC42 compass, similar to FC40, including performance and environmental ratings.
Specifications for the RF300 rudder feedback unit, including angle and linearity.
Specifications for the RF25 rudder feedback unit, including angle and accuracy.
Technical details for the R3000X remote control, including dimensions and environmental protection.
Specifications for the JS10 joystick, including environmental protection and shock resistance.
Technical parameters for the SimNet network, including cable length and bit rate.
Explanation of IP rating system for equipment protection against solids and liquids.
Details and wiring for the AT10 converter, enabling SimNet to NMEA0183 communication.
Table showing data converted between SimNet/NMEA2000 and NMEA0183 sentences.
To Next Page
