Skymaster ARF PLUS PRO HAWK 100 - User Manual

The Bae Hawk T1 and Hawk 100 by Skymaster
Thank you very much for purchasing our Skymaster ARF PRO Hawk . Please note that the photos in this instruc-
tion manual show certain views from the prototypes. The instruction manual is same for T1 and 100 models. Some
modifications and upgrades might have taken place by the release of the model. We have tried to produce a very
scale replica of this classic jet. This manual describes the assembling of “ PRO” model. Speed brake, Landing gear
and doors are factory installed. Before you start building and setting-up your aircraft, please make sure you have
read this instruction manual, and understood it. If you have any questions, please don’t hesitate to contact us. Be-
low are the contact details:
Office Taiwan:
No.9.39 Lane,Yuag-Chang 2nd Street, Ren-Wu Hsiang, Kaohsiung Hsien, 814, Taiwan, R.O.C.
TEL: +886 9 3299 7923
FAX: + 886 7373 1215
http://www.skymasterjet.com
Sales : skymasterjets@263.net
Technical support : morne.m@pixie.co.za
Spesifications Hawk 100
Type : T.A.V.S ARF PRO
Scale : 1/4.75
Length : 97.5”: (2480mm)
Span : 78 3/4”: (2000mm)
Weight : 38—42Lbs ( 16—19 Kg)
Engine : 27—36Lbs (12—16 Kg) trust
Radio : 12 Channel (10—12 servo’s)
SM © 2009
1/4.75 Scale Almost-Ready-To-Fly RC Jet
Assembly and operations manual

Summary

Operational Safety Warnings

General Safety Precautions

Crucial warnings for safe operation of the jet model.

Range Check Procedures

Importance of thorough R/C system range checks before flight.

Engine Start Safety

Precautions for starting the engine safely.

Handling and Hinges

Handling & Transporting

Guidelines for safe handling and transport of the composite model.

Tools and Adhesives

Essential Tools

Lists essential tools for building the model.

Recommended Adhesives

Recommends specific glues and adhesives for composite parts.

Assembly Guidelines

Health Precautions

Safety measures for working with fiberglass and paints.

Radio Equipment and Accessories

Radio Equipment Selection

Guidance on selecting and installing radio control systems.

Recommended Accessories List

List of recommended servos, valves, and other parts.

Kit Contents

Wing Assembly

Servo Mounting and Pushrods

Fit servos, horns, and pushrods for ailerons and flaps.

Flap Servo Installation

Install flap servos, horns, and pushrods.

Stabilizer Assembly

Fin and Rudder Assembly

Fuselage Assembly

Nose Retract Unit Installation

Install nose retract unit and steering servo.

Tailpipe and Fuel System

Fuel Cell Preparation and Plumbing

Rinse tank, make clunk, fit pipes, and plumb.

Air System Installation

Air System Plumbing Details

Plumb landing gear, doors, brakes, and speed brake.

Turbine Installation

Turbine Mounting and Securing

Secure turbine to rail, ensure gap from tailpipe.

Wiring and Fuel Line Management

Run turbine wires, power cables, and install fuel pump.

Electrical Connection Guide

Pictures showing electrical connections.

Equipment Installation

Neat and Logical Installation

Install equipment neatly and logically for easier service.

Forward Weight Distribution

Install equipment forward to prevent tail-heavy condition.

Pre-Flight Checks

Center of Gravity (CG) Adjustment

CG location for safe flight, warning against moving it back.

Range and Speed Checks

Perform radio range checks and set maximum speed.

Flight Operations

Take-Off Procedure

Select takeoff flaps, throttle up, and lift off.

Slow Flight Handling

Explore slow speed handling and stall characteristics.

Landing Approach and Execution

Approach, deploy flaps/gear, flare, and land.

Skymaster ARF PLUS PRO HAWK 100 Specifications

General

Wingspan	1000mm
Power System	Electric
Servos	9g x 4
Material	EPO Foam
Skill Level	Intermediate
Motor	Brushless
Battery	11.1V LiPo
Radio	4 Channel