SMA 5000TL - User Manual

Questions and Answers

J
Jessica SmithSep 9, 2025
What does Vac-Bfr or Vac-Srr mean on SMA 5000TL?
- C
  challSep 9, 2025
  If your SMA Inverter shows 'Vac-Bfr' or 'Vac-Srr', the grid voltage is outside the permissible range. Check the grid current and connection at the inverter. If the voltage is outside the acceptable range due to local grid conditions, contact the utility operator to adjust the voltage or request changes to the monitored operational limits (Vac-Min and Vac-Max). If the grid frequency is within the tolerable range, yet the errors persist, contact the SMA Serviceline.
J
Jeremy JordanSep 8, 2025
What causes Fac-Bfr, Fac-Srr or FacFast error on SMA 5000TL?
- M
  Mathew LarsonSep 8, 2025
  If your SMA Inverter displays “Fac-Bfr,” “Fac-Srr,” or “FacFast,” the grid frequency is outside the permissible range. Check the grid connection and contact the utility operator if necessary. If the grid frequency is within the tolerance range, yet the faults persist, contact the SMA Serviceline.
K
ksimmonsSep 7, 2025
Why does my SMA Inverter show ACVtgRPro error?
- S
  shawnflemingSep 7, 2025
  The 'ACVtgRPro' error on your SMA Inverter means the 10-minute-average grid voltage is outside the permissible range, possibly due to high grid voltage or impedance at the connection point. Check the grid voltage at the inverter's connection point. If it's consistently 253 V or higher due to local grid conditions, contact the utility operator to adjust the voltage or request an alteration of the ACVtgRPro parameter's threshold. If the grid voltage is within the acceptable range and the error persists, contact the SMA Serviceline.
A
Alicia DominguezAug 22, 2025
What to do if my SMA 5000TL shows '!PV-Overvoltage! - !DISCONNECT DC!'?
- S
  Sarah BowersAug 23, 2025
  If your SMA Inverter displays '!PV-Overvoltage! - !DISCONNECT DC!', this indicates overvoltage at the DC input. You should disconnect the miniature circuit-breaker, remove the ESS, and unlock and remove all DC connectors using a screwdriver. Then, verify that the DC voltage is below the inverter's maximum input voltage.
C
Christine GardnerSep 5, 2025
How to fix PV overvoltage on SMA 5000TL Inverter?
- D
  David DonaldsonSep 5, 2025
  If your SMA Inverter displays 'PV-Overvoltage' and instructs you to disconnect DC, it indicates an overvoltage at the DC input, which can damage the inverter. Immediately disconnect the inverter from the grid by: 1. Turning off the line circuit breaker. 2. Removing the Electronic Solar Switch. 3. Disconnecting all the DC plug connectors. Then, check the DC voltage. If it exceeds the maximum input voltage, inspect the plant design or contact the PV generator installer. If the voltage is within the limit, reconnect the inverter. If the message reappears, disconnect the inverter and contact the SMA Serviceline.
T
tonyamedinaSep 3, 2025
What does DC fuse mean on my SMA Inverter?
- K
  Keith CooperSep 4, 2025
  If your SMA Inverter displays 'DC fuse', it indicates that at least one of the string fuses has tripped or is defective. Check the function of the string fuses.
B
Brittany ThompsonSep 2, 2025
What causes damage to the SMA 5000TL due to moisture and dust intrusion?
- D
  Dale BrownSep 2, 2025
  Damage to the SMA Inverter from moisture and dust intrusion can occur if the ESS is not plugged in or incorrectly plugged in during operation. Always plug in the ESS until it is flush with the enclosure and ensure that the gap between the ESS and the enclosure is no more than 1 mm.
E
estradajessicaSep 1, 2025
What does 'Check Varistor' mean on my SMA 5000TL?
- J
  Jacob SantosSep 1, 2025
  If your SMA Inverter displays 'Check Varistor', it indicates that at least one of the varistors is defective. Check the function of the varistors.
J
Jose AlexanderAug 31, 2025
Why all LEDs have gone out on my SMA 5000TL?
- D
  David CraigAug 31, 2025
  If all three LEDs have gone out on your SMA Inverter, the inverter is switched off because the ESS is not plugged in or there is no irradiation.
A
Amy MccoyAug 29, 2025
What to do if my SMA 5000TL displays 'dI-Bfr dI-Srr'?
- D
  Donna PriceAug 30, 2025
  If your SMA Inverter displays 'dI-Bfr dI-Srr', it means that the inverter has detected a change in the differential current. Make sure that the PV plant is insulated correctly and that there is no earth fault.

SMA 5000TL Specifications

General

Nominal AC power	5000 W
Topology	Transformerless
Nominal AC voltage	230 V
Number of MPP trackers	2
Operating Temperature Range	-25 °C to +60 °C
Cooling	Convection
Protection Degree	IP65
AC voltage range	180 V - 280 V