Why is my Smeg WHT710ECIT washing performance is poor and laundry turns gray?
If your Smeg Washer is not performing well and laundry turns gray, it could be due to: * Insufficient detergent over time: Use the recommended amount of detergent. * Washing at low temperatures for too long: Select the proper temperature for the laundry. * Insufficient detergent with hard water: Use the recommended amount for hard water.
What to do if my Smeg WHT710ECIT does not drain water?
If your Smeg Washer isn't draining, the issue might be a clogged or twisted drain hose. Try cleaning or flattening the hose. Alternatively, the pump filter could be clogged, so cleaning the pump filter might solve the problem.
Why does my Smeg WHT710ECIT laundry does not smell like the softener?
If your laundry doesn't smell like softener after washing in your Smeg Washer, it might be because: * Detergent is in the wrong compartment: Ensure detergent is not in the prewash compartment when a prewash cycle isn't selected. Clean the dispenser with hot water and put the detergent in the correct compartment. * Detergent is mixed with softener: Do not mix softener with detergent. Clean the dispenser with hot water.
Why is there detergent residue in the detergent drawer of my Smeg WHT710ECIT?
Detergent residue in the drawer of your Smeg Washer can occur because: * The drawer was wet when you added detergent: Dry the drawer before adding detergent. * The detergent has gotten damp: Store detergents properly in a dry environment. * Low water pressure: Check the water pressure. * Blocked compartment holes: Check and clean the holes if they are clogged. * Detergent mixed with softener: Do not mix; wash and clean the dispenser with hot water.
Why does Smeg WHT710ECIT laundry became stiff after washing?
Laundry can become stiff after washing in your Smeg Washer for a couple of reasons: * Insufficient detergent: Use an appropriate amount of detergent based on water hardness. * Detergent in wrong compartment: Put the detergent in the correct compartment, not the prewash if prewash cycle is not selected. * Detergent mixed with softener: Do not mix; wash the dispenser with hot water.
Why my Smeg WHT710ECIT Washer does not fill with water?
If your Smeg Washer isn't filling with water, check the following: * Ensure the tap is turned on. * Make sure the water inlet hose isn't bent; flatten it if it is. * Check if the water inlet filter is clogged and clean it if necessary. * Confirm that the loading door is fully closed.
Why my Smeg Washer programme cannot be started or selected?
If the programme on your Smeg Washer cannot be started or selected, it may have switched to self-protection mode due to a supply problem such as line voltage or water pressure. To resolve this, press and hold the On / Off button for 3 seconds.
Why does my Smeg WHT710ECIT take longer than specified?
Several factors can cause your Smeg Washer to take longer than expected: * Low water pressure: The machine waits for adequate water intake. * Low voltage: Washing time is prolonged to ensure proper cleaning. * Low input water temperature: Heating the water takes longer. * Increased rinsing: The machine may increase rinse water or add an extra rinse. * Excessive foam: The automatic foam absorption system may activate due to too much detergent. In this case, use the recommended amount of detergent.
Why does my Smeg WHT710ECIT vibrate or make noise?
Your Smeg Washer may vibrate or make noise due to several reasons: * The machine might be unbalanced: Adjust the feet to level it. * There might be a hard substance in the pump filter: Clean the pump filter. * Transportation safety bolts might not be removed: Remove these bolts. * The laundry quantity might be too little: Add more laundry. * The machine might be overloaded: Remove some laundry or distribute the load evenly. * The machine might be leaning on something: Ensure it's not.
Why does my Smeg WHT710ECIT Washer not switch to spinning step?
Your Smeg Washer might not switch to the spinning step due to: * Unbalanced load: The automatic unbalanced load detection system may be activated. * Incomplete draining: Check the filter and drain hose to ensure water is completely drained. * Excessive foam: Too much detergent can activate the automatic foam absorption system. Use the recommended amount of detergent.
To Next Page
General
