Snapper COMMERCIAL WALK-BEHIND - Backside Idler (PP7140 KWV)

59
BACKSIDE IDLER
ITEM PART NO. DESCRIPTION
-- 6-1207 KIT, Backside Dual Idler (Pistol Grip) (Includes items 1 thru 46)
1 2-4708 PULLEY, 3-1/4” (transmission out) (2)
2 2-4713 FENDER, Left (not shown)
3 2-4714 FENDER, Right (shown)
4 2-4891 BELT, PRO 7 Traction (2RA Section, 50.96” Effective Length)
5 3-3718 FLANGE, Output (2)
6 9-0548 SCREW, 1/4-20 x 1” Hex Head Cap, Grade 5
7 9-0583 NUT, 1/4-20 Hex Flange Lock (2)
8 5-2991 ASSEMBLY, Tank Bracket (Includes items 9 thru 32)
9 1-0739 RING, 5/8” External Retaining (4)
10 2-2768 STUD, Fender Mount (3/8-16 thread) (2)
11 2-4707 PULLEY, 3-1/4” Idler (4)
12 2-4717 SPRING, Extension (2)
13 3-3713 LINK, Short (2)
14 3-3714 LINK, Long Right Hand (not shown)
15 3-3715 LINK, Long Left Hand (shown)
16 3-3720 ARM, Brake (2)
17 3-3726 FORM, Tank Bracket
18 4-1357 WELDMENT, Idler Lower Left/Upper Right (2)
19 4-1358 WELDMENT, Upper Left/Lower Right (2)
20 4-1359 WELDMENT, Idler Pivot Right Hand
21 4-1360 WELDMENT, Idler Pivot Left Hand
22 7-6979 NUT, 3/8-16 Hex Nyloc (12)
23 9-0038 PIN, 3/32 x 1” Cotter (6)
24 9-0122 WASHER, 3/8” Flat (2)
25 9-0136 BOLT, 3/8-16 x 3/4” Square Neck, Grade 2 (2)
26 9-0206 SCREW, 5/16-18 x 3/4” Hex Head Cap, Grade 5 (2)
27 9-0585 NUT, 5/16-18 Hex Flange Lock (2)
28 9-0588 SCREW, 3/8-16 x 2” Hex Head Cap, Grade 5 (2)
29 9-0637 SCREW, 3/8-16 x 2-1/2” Hex Head Cap, Grade 5 (2)
30 9-0665 NUT, 3/8-16 Hex Jam (2)
31 9-0747 BOLT, 3/8-16 x 1” Round Head Square Neck, Grade 5 (12)
32 7-6998 FITTING, Grease, 1/4-28 Thread (4)
33 1-2306 BUSHING, .381 I. D. Flange (2)
34 1-6231 PIN, #13 Hair (2)
35 2-4590 PIN, Reverse PG (2)
36 2-4607 SWIVEL, Brake Link PM (2)
37 9-0563 SCREW, 3/8-16 x 1” Hex Head Cap, Grade 5 (2)
38 9-1294 WASHER, 1/4” Flat (2)
39 2-4710 ROD, Traction, Pistol Grip (2)
40 3-3719 STRAP, Brake Pistol Grip, Left Side
41 3-3725 STRAP, Brake Pistol Grip, Right Side
42 3-3687 LEVER, Reverse, Pistol Grip
43 2-4589 CHAIN, Reverse, Pistol Grip
44 3-3798 ARM, Reverse
45 9-1175 NUT, M6 Hex Lock
46 9-1176 SCREW, M6 x 14 Hex Head Cap
NOTE: Kit 6-1207 will fit model PP71250KW (Pistol Grip) PRO Commercial; Mower
MANUAL No. 06929 COMMERCIAL WALK-BEHIND ACCESSORIES