What to do if SolarEdge SE3680H shows 'Over Temperature'?
If your SolarEdge Inverter displays 'Over Temperature', verify proper clearances around the inverter and EV Charger Cable. After verification reconnect the EV charger cable to the EV.
Why is the string voltage lower than the number of optimizers on my SolarEdge SE3680H?
If your SolarEdge Inverter displays 'String voltage not 0V but lower than number of optimizers', it can be caused by: * Power optimizer(s) not connected in the string. Connect all power optimizers. * Panel(s) not connected properly to power optimizer inputs. Connect the modules to the optimizer inputs. * String reverse polarity. Check string polarity using a voltmeter and correct if needed.
Why is the string voltage higher than the number of optimizers on my SolarEdge SE3680H?
If the SolarEdge Inverter displays 'String voltage is higher than number of optimizers', it could be due to several reasons: * An extra power optimizer is connected in the string. * A module is connected directly to the string, without a power optimizer. * Power optimizer(s) malfunction. In this case: 1. Disconnect the wires connecting the power optimizers in the string. 2. Measure the output voltage of each power optimizer to locate the power optimizer that does not output 1V safety voltage. 3. If a malfunctioning power optimizer is located, check its connections, polarity, module, and voltage. 4. Contact SolarEdge Support.
What to do if the SolarEdge SE3680H Inverter shows 'Gateway not responding'?
If your SolarEdge Inverter shows 'Gateway not responding', it means the ping to the router failed. Check the physical connection to the switch/ router. Check that the link LED at the router /switch is lit (indicating phy-link). If OK - contact your network IT, otherwise replace the cable or change it from cross to straight connection.
How do I resolve a 'No DHCP' error on my SolarEdge SE3680H Inverter?
If your SolarEdge Inverter displays 'No DHCP', it indicates an IP settings issue. Check the router and configuration. Consult your network IT.
How to troubleshoot 'LAN cable disconnected' error on SolarEdge SE3680H?
If your SolarEdge Inverter displays 'LAN cable disconnected', it means there is a physical connection fault. Check the cable pin- out assignment and cable connection.
How to fix No Internet connection on SolarEdge SE3680H Inverter?
If your SolarEdge Inverter displays 'No Internet connection', it means the ping to google.com failed. You should connect a laptop and check for internet connection. If internet access is unavailable, contact your IT admin or your internet provider. For Wi-Fi networks, ensure that user-name and password are as defined in the internet provider AP/ router.
What to do if SolarEdge SE3680H displays 'Pairing failed'?
If the SolarEdge Inverter displays 'Pairing failed' and the power optimizers are shaded, and if you connected the inverter to the monitoring platform, retry pairing remotely when there is sunlight. Make sure to leave the inverter ON/OFF/P switch ON and that S_OK appears in the status screen.
General| AC Output Power | 3680 W |
|---|---|
| Protection Rating | IP65 |
| Rated AC Power | 3680 W |
| AC Frequency | 50/60 Hz |
| Max. Input DC Voltage | 480 Vdc |
| Number of MPP Trackers | 1 |
| Warranty | 12 years |
| Cooling | Convection |
| Operating Temperature Range | -25°C to 60°C |
| AC Voltage | 220/230 V |
Explains the meaning of various safety symbols used within the document.
Describes DC-DC converters that maximize power harvesting at the module level.
Explains the platform for monitoring technical and financial performance of SolarEdge sites.
Details the inverter's function in converting DC to AC and EV charging capabilities.
Lists the standard tools and equipment recommended for installing the SolarEdge system.
Outlines essential safety notes and warnings applicable when installing power optimizers.
Provides guidelines for installing power optimizers, including string length and cable rules.
Lists the items included in the inverter package for installation.
Explains how to identify the inverter using its serial number and electrical ratings.
Shows the connectors and interfaces on the inverter and connection unit.
Details the EV charger connector, LED indicator, and other ports on the connection unit.
Describes the ON/OFF/P switch and inverter LED indicators for status.
Explains how to set the circuit breaker rating DIP switches on the connection unit.
Details the buzzer indications for different EV charger events like connection and errors.
Provides instructions and clearance requirements for mounting the inverter.
Guides on selecting and configuring Residual Current Devices for system protection.
Instructions for activating the installation using the SetApp mobile application.
Steps for commissioning and configuring inverter settings via the SetApp.
How to configure country, grid, and language settings for inverter compliance.
Procedure for pairing the inverter with power optimizers and system components.
Details on configuring communication settings for monitoring platform connectivity.
Information on power control options like Grid Control and Energy Manager.
Steps to verify the proper activation and commissioning of the SolarEdge system.
How to access and interpret the system status screen for inverter settings and operation.
Details on the main inverter status screen, including power, voltage, and connectivity.
Shows the accumulated status of all inverters connected in a chain and the leader inverter status.
Displays the status of various communication options like LAN, RS485, Wi-Fi, and Cellular.
Shows the total energy produced by the inverter over different periods.
Details the status of production and export meters connected to the inverter.
Displays the EV charging status, mode, and energy added to the EV.
Instructions for connecting the site to the monitoring platform for data reporting.
Explains the features and benefits of the SolarEdge monitoring platform.
Guides on creating logical and physical layouts for system components in the platform.
Information on using the Designer tool for inverter and optimizer selection and report generation.
Details on using the smartphone app to scan components and create a PV site map.
Instructions for accessing the site creation page and mapping physical layouts.
How to use a physical layout template and stickers for mapping PV site components.
Lists the available communication types for transferring monitored information.
Instructions for establishing an Ethernet connection for LAN communication.
Details the available RS485 ports for connecting multiple devices.
How to use Wi-Fi connection for linking the inverter to the monitoring platform.
Information on using a cellular connection for wireless monitoring via a plug-in.
Describes the functionality of the communication gland openings for various connection types.
Step-by-step guide to connect the inverter to the monitoring platform via Ethernet.
Instructions for connecting multiple inverters in a bus configuration using RS485.
Steps to check if the communication connection to the monitoring server is successfully established.
Methods to identify system errors indicated by LEDs, codes, or the monitoring platform.
Troubleshooting steps for common errors related to the EV charger function.
Guides for troubleshooting communication issues with Ethernet and RS485 connections.
Specific steps to troubleshoot RS485 communication problems, like leader not found.
General troubleshooting steps for network and modem connectivity issues.
Procedure for replacing the fuse located in the inverter.
Step-by-step guide for replacing an existing inverter with a new one.
Instructions for replacing the connection unit of the inverter system.
Details on setting DIP switches for Modbus address and RS485 termination.
Configuration of Modbus addresses for the energy meter using DIP switches.
Configuration of RS485 wiring termination using DIP switches on the energy meter.
Technical data for inverter AC/DC output, voltage, current, efficiency, and compliance.
Specifications related to cable diameter, cross-section, dimensions, and weight.
Default voltage and frequency trip limits and clearing times compliant with IEEE1547.
Technical details for the EV charger, its charging modes, and cable specifications.
Provides dimensional drawings and specifications for the inverter unit.
Contact details and required information for technical support with SolarEdge products.
To Next Page
