4746
4
If the nozzle opening is blocked, you can use the pin on the cleaning tablet holder to remove the
blockage. If you cannot unblock the nozzle with the pin, rinse the nozzle with warm water and try
again.
33. Rinse the nozzle in warm water.
34. Gently screw the nozzle back onto the steaming wand 5.
35. Clean the appliance and the water tank 8 with a soft and damp cloth.
36. Dry the appliance and the water tank 8.
37. Plug in and switch on the appliance.
V REPLACING THE WATER FILTER CARTRIDGE
Replace the water lter cartridge when the corresponding alarm is visible.
1. Switch o and unplug the appliance.
2. Remove the water tank 8 from the appliance (see image G).
3. Empty the water tank 8 above a sink.
4. Remove the water lter cartridge 9 from the water tank 8.
5. Hold the new water lter cartridge 9 in a container with water.
4
Use the INTENZA water lter cardridge (Art.-no. 700.78) which is available in selected countries.
6. Gently squeeze the water lter cartridge 9 to remove air bubbles from the lter.
7. Rinse the water tank 8 with water.
8. Insert the water lter cartridge 9 into the bracket in the water tank 8 with the selector facing
downwards.
9. Fill the water tank 8 with water up to the MAX marking.
10. Insert the water tank 8 into the appliance.
11. Place a container (min. 500 ml) underneath the brewing head 4.
12. Plug in and switch on the appliance.
13. Press the programming button d.
14. Press the single cup extraction button j to activate the automatic rinsing cycle.
When the appliance beeps twice and the cup extraction buttons light up white, the appliance is ready for
use.
V USING THE BREWING HEAD CLEANING CYCLE
Clean the appliance with a cleaning tablet when the corresponding alarm is visible.
For cleaning the brewing head, please use a cleaning tablets which are suitable for espresso machines.
4
For best results, we recommend SOLITABS (Art.-no. 993.02) which is available in selected countries.
To clean the appliance with a cleaning tablet:
1. Plug in and switch on the appliance.
2. Place the double cup lter p into the portalter s.
3. Place the rubber insert for cleaning i into the double cup lter p (see image H) and put a
SOLITABS cleaning tablet on top.
4. Insert and rotate the portalter s into the brewing head 4 (see image C). Make sure the handle
is aligned with the CLOSE marking.
5. Place a container underneath the portalter s.
6. Press the programming button d.
7. Press the double cup extraction button k to start the rinsing procedure.
The procedure has 8 cycles with pauses of 30 seconds. The cycle number and pause time are shown on
the display.
V MONTHLY MAINTENANCE
We recommend cleaning the appliance every month. To clean the appliance:
1. Plug in and switch on the appliance.
2. Set the grind size selector g to COARSE.
3. Close the hopper gate at the back of the bean container 1.
4. Place a container under the portalter holder 3.
5. Press the grind time knob c to switch on the grinder and remove excess coee.
6. After a few seconds, press the grind time knob c again to switch o the grinder.
7. Switch o the appliance and remove the bean container 1 (see image E).
8. Empty the bean container 1.
6 Always remove the bean container (see image E) rst and only then remove
the grinder mechanism. Do not take o both parts together and never use
excessive force to remove the parts.
9. Reassemble the bean container 1 (see image F).
10. Fill the bean container 1 with GRINDZ
TM
which is available in selected countries.
4
You can buy GRINDZ
TM
at your supplier or Solis (art. No. 993.08).
11. Open the hopper gate at the back of the bean container 1.
12. Place a container under the portalter holder 3.
13. Switch on the appliance.
14. Press and hold the grind time knob c to switch on the grinder.
15. When all GRINDZ
TM
has run through the appliance, release the grind time knob c to switch o the
grinder.
16. Close the hopper gate.
17. Switch o the appliance and remove the bean container 1 (see image E).
18. Empty the bean container 1.
19. Rinse the bean container 1 with warm water and a mild detergent.
20. Rinse the bean container 1 with clean water.
21. Dry the bean container 1 thoroughly.
22. Reassemble the grinder and the bean container 1. Make sure all parts lock in place.
23. Fill the bean container 1 with coee beans.
24. Open the hopper gate at the back of the bean container 1.
25. Switch on the appliance.
26. Press and hold the grind time knob c to switch on the grinder.
27. After 20 seconds, release the grind time knob c again to switch o the grinder.
28. Set the grind size selector g back to the desired position.
29. Switch o and unplug the appliance.
4
Make sure the portalter is not hot when removing the spout.
30. Unscrew the spout of the portalter s.
31. Soak the following parts in warm water and a mild detergent:
• Portalter s (only the metal parts).
• Cup lters p a
• Spout
32. Unscrew the steaming nozzle from the steaming wand 5.
To Next Page
Loading...
Need help?
General
