45
SAFETY AND REGULATORY INFORMATION
FEDERAL COMMUNICATION COMMISSION
INTERFERENCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received,
including interference that may cause undesired
operation.
This device has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy, and if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
FCC COMPLIANCE STATEMENT
• Any changes or modifications not expressly approved
by the party responsible for compliance could void the
user‘s authority to operate the equipment.
• The antenna(s) used for this transmitter must not
be co-located or operating in conjunction with any
other antenna or transmitter.
• The country code selection is for non-US model
only and is not available to all US model. Per
FCC regulation, all Wi-Fi product marketed in
US must fixed to US operation channels only.
This EUT is compliance with SAR for general population/
uncontrolled exposure limits in IC RSS-102 and had been
tested in accordance with the measurement methods and
procedures specified in IEEE 1528 and IEC 62209. This
equipment should be installed and operated with minimum
distance 15 mm between the radiator and your body.
This device and its antenna(s) must not be co-located
or operating in conjunction with any other antenna or
transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor
usage only.
Ce dispositif a été testé pour la conformité avec les valeurs
SAR à un fonctionnement typique près du corps . Pour
assurer que les niveaux d'exposition aux radiofréquences
en deçà des niveaux testés, utiliser des accessoires avec
cet équipement pour maintenir une distance de séparation
minimale de 15 mm entre le corps de l'utilisateur et l'appareil.
Lorsque l'appareil est réglé sur le mode point chaud, veuillez
l'utiliser à au moins 10mm de votre corps. Ces accessoires
ne doivent pas contenir des composants métalliques. Il est
possible que les accessoires utilisés près du corps qui ne
répondent pas à ces exigences ne sont pas compatibles
avec les limites SAR et il est conseillé d'éviter de les utiliser.
Les opérations dans la bande de 5.15-5.25GHz sont limitées
à un usage intérieur seulement
This device complies with Industry Canada license-exempt
RSS standard(s).
Operation is subject to the following two
conditions:
1. This device may not cause interference.
2.
This device must accept any interference, including
interference that may cause undesired operation of
the device.
et appareil est conforme avec Industrie Canada RSS
exemptes de licence standard(s).
Son fonctionnement est soumis aux deux conditions
suivantes:
(1) cet appareil ne peut pas provoquer d'interférences, et
(2) cet appareil doit accepter toute interférence, y compris celles
pouvant causer un mauvais fonctionnement de l'appareil.
This Class B digital apparatus complies with Canadian
CAN ICES-003(B) / NMB-003(B).
Cet appareil numérique de la classe B est conforme à la
norme CAN ICES-003(B) / NMB-003(B) du Canada.
ISED RF EXPOSURE STATEMENT (IC)