20
HCD-GPX6/GPX7
[CD REPEAT 5 LIMIT CANCEL MODE]
Number of repeat for CD playback is 5 times when the repeat
mode is “REPEAT”. This mode enables CD to repeat playback for
limitless times.
Procedure:
1. Press the I/1 button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press three buttons of . m (CD), x (TAPE), and
[DSGX] simultaneously.
4. It enters the CD repeat 5 limit cancel mode and display “LIMIT
OFF”
5. To release this mode, press the I/1 button to turn the power
off.
[CD SHIP MODE]
This mode can run the CD sled motor optionally. Use this mode,
for instance, when cleaning the optical pick-up.
Procedure:
1. Press the I/1 button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press three buttons of [TUNING MODE], x (CD),
and I/1 simultaneously. *1
4. Set to the CD ship mode. (chucking on)
5. After blink “STANDBY”, “LOCK” is displayed, disconnect
the AC plug.
*1) If press three buttons of [DIRECTION], u (CD), and
[DSGX] simultaneously, Activate the CD ship mode and
MC cold reset.
[CD SLOT LOCK]
This mode is for the antitheft of CD disc in shop. (not for trans-
port)
Procedure:
1. Press the I/1 button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Insert a disc.
4. While pressing the x (CD) button, press the A (CD) button
for more 5 seconds.
5. The message “LOCKED” is displayed and the disc slot is
locked. (Even if exiting from this mode, the disc slot is still
locked)
6. If press the A (CD) button to eject the disc, the message
“LOCKED” is displayed and can not eject the disc.
7. To release this lock, while pressing the x (CD) button, press
the A (CD) button for 5 seconds again.
8. The message “UNLOCKED” is displayed and the disc slot is
unlocked.
[CD POWER MANAGE]
This mode is for switch the CD power supply on/off. Even if this
state pulls out AC plug, it is held.
Procedure:
1. Press the I/1 button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press the I/1 button again to turn the power off (standby).
4. While pressing the x (CD) button, press the I/1 button.
5. It turns power on and display “CD POWER”, then display
“ON” or “OFF”.
[CHANGE-OVER THE AM TUNING INTERVAL]
(EXCEPT AEP model)
The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1. Press the I/1 button to turn the power on.
2. Press the [BAND, TUNER] button to select TUNER (AM) func-
tion.
3. Press the I/1 button again to turn the power off (standby).
4. While pressing the [TUNING +] button, press the I/1 button.
5. It turns power on and display “STEP 9kHz” or “STEP 10kHz”,
and thus the tuning interval is changed over.
[MD/VIDEO FUNCTION CHANGE]
Select either VIDEO or MD of the external input.
Procedure:
1. Press the I/1 button to turn the power on.
2. Press the [FUNCTION] button to select MD or VIDEO func-
tion.
3. Press the I/1 button again to turn the power off (standby).
4. While pressing the [FUNCTION] button, press the I/1 but-
ton.
5. The another function of the previous function is selected and
display “MD” or “VIDEO”.
To Next Page
