What to do if my Sony VPL-ES3 Projector power is not turned on?
If your Sony Projector is not turning on, it could be due to a few reasons. If the power has been turned off and on with the ?/1 key at a short interval, wait for about 45 seconds before attempting to turn it on again. Ensure that the lamp cover is securely closed and the air filter cover is properly attached.
What to do if my Sony VPL-ES3 has no picture?
If your Sony Projector displays no picture, first ensure all cables are correctly and securely connected. If your computer is DDC compatible, connect the projector to the computer, turn the projector on, and then start the computer. Also, select the correct input source using the INPUT key. Make sure the computer signal is set to output only to an external monitor. If you are using a notebook or an all-in-one LCD, you may need to switch the computer to output to the projector using specific keys or settings; refer to your computer's operating instructions for details.
How to fix a Sony Projector that is not turning on?
If your Sony Projector is not turning on, it might be due to a couple of reasons. If the power has been turned off and on quickly, wait about 45 seconds before trying again. Ensure that the lamp cover and the air filter cover are securely closed and attached, respectively.
Why is there no picture on my Sony VPL-ES3 Projector?
There could be several reasons why there's no picture on your Sony Projector. Ensure all cables are properly connected. This projector is compatible with DDC2B (Digital Data Channel 2B). If your computer is compatible with DDC, turn the projector on according to the following procedures: 1 Connect the projector to the computer. 2 Turn the projector on. 3 Start the computer. Also, verify that you've selected the correct input source using the INPUT key, and confirm that picture muting is not enabled by pressing the PIC MUTING key.
Why is the picture too dark on my Sony Projector?
If the picture on your Sony Projector is too dark, it might be due to improperly adjusted contrast or brightness. Adjust these settings on the “Adjust Picture...” menu. Alternatively, the lamp may have burnt out or is dim, requiring replacement with a new one.
How to fix incorrect color balance on Sony Projector?
If the color balance on your Sony Projector is incorrect, try adjusting the picture settings. Also, ensure that the “Color System” setting on the SET SETTING menu matches the color system being input.
What to do if the image extends beyond the screen on Sony Projector?
If the image extends beyond the screen on your Sony Projector, and if there are black edges around the image, display the full image on the screen and press the APA key. Adjust “Shift” on the INPUT SETTING menu properly. If this input signal cannot be projected as the frequency is out of the acceptable range of the projector, input a signal that is within the range of the frequency. If the resolution setting of the output signal of the computer is too high, set the output setting to SVGA (VPL-ES3) or XGA (VPL-EX3).
Why is my Sony VPL-ES3 picture not clear?
If the picture on your Sony Projector is not clear, try adjusting the focus. If condensation has accumulated on the lens, leave the projector for about two hours with the power on.
What does it mean when the LAMP/COVER indicator is flashing on my Sony Projector?
If the LAMP/COVER indicator is flashing on your Sony Projector, ensure that the lamp cover and the air filter cover are securely attached.
What does it mean when the LAMP/COVER indicator lights up on my Sony VPL-ES3?
If the LAMP/COVER indicator lights up on your Sony Projector, the lamp may have reached the end of its life and needs to be replaced. Alternatively, the lamp may have reached a high temperature; wait for 45 seconds to cool the lamp before turning the power on again.
General| Matrix size | 0.63 \ |
|---|---|
| Heat dissipation | 750.7 BTU/h |
| Projection distance | - m |
| Projection technology | LCD |
| Contrast ratio (typical) | 300:1 |
| Screen size compatibility | - \ |
| Projector native resolution | SVGA (800x600) |
| Digital zoom | 1.2 x |
| Focal length range | - mm |
| Dimensions (WxDxH) | 308 x 252 x 98 mm |
| Power requirements | AC 100 - 240V, 50/60Hz |
| Lamp power | 165 W |
| Light source type | Lamp |
| Service life of light source | 2000 h |
| Number of built-in speakers | 1 |
| Noise level | 29 dB |
| Power consumption (standby) | 10 W |
| Power consumption (typical) | 220 W |
| Storage temperature (T-T) | -20 - 60 °C |
| Operating temperature (T-T) | 0 - 35 °C |
| Storage relative humidity (H-H) | 10 - 90 % |
| Operating relative humidity (H-H) | 35 - 85 % |
| Safety | UL60950, cUL (CSA No.60950-1), FCC Class B, IC Class B, CB (IEC 60950-1), FIMKO (EN60950), CE (LVD, EMC), C-Tick, VCCI, JEITA, DENAN, CCC, NOM, SASO, MIC, PSB |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Ethernet LAN | No |
| Product color | Black, White |
Weight and Dimensions| Weight | 2900 g |
|---|
Covers fire, electric shock, earthing, and power switch safety guidelines.
Details power cord use, battery caution, regional warnings, and disposal.
General Precautions: Ventilation, Heat, Cleaning, LCD Characteristics.
Unsuitable Environments: Dust, Smoke, Altitude, Ventilation Blocking.
Key Features: Brightness, Picture Quality, Quiet Operation, Security.
Control Panel Layout: Buttons, Ports, Indicators.
Remote Commander and Connections: Operation, Ports, Signal Inputs.
Installation and Setup: Placement, Distance, Source Connection.
Picture Adjustment and Power Off: Image Settings, Keystone, Shutdown.
Menu Language and Security Lock: Changing Display Language, Enabling Lock.
Digital Zoom and Freeze: Image Magnification and Pausing.
Menu Navigation: Accessing, Clearing, Resetting Options.
Picture and Input Settings: Modes, Contrast, Brightness, Signal Sources.
System, Install, Info Settings: General Config, Installation Options, Status.
Signal Compatibility: Adjustable Settings by Input Type.
Lamp Replacement: Procedure, Safety, and Disposal.
Air Filter Cleaning: Maintenance Steps and Importance.
Power/Picture Issues: No Power, No Picture, Noisy Image Solutions.
Indicator/Message Solutions: Lights, Errors, Panel Key Lock.
Specs: Optical, Electrical, Input/Output Parameters.
Connector Pinouts: Detailed Pin Assignments for Ports.
Preset Signals: Frequencies, Sync, and Compatibility Tables.
Installation Diagrams: Visual Guides for Floor and Ceiling Mounting.
Physical Dimensions: Projector Size Views and Measurements.
To Next Page
