How to fix Sony VPL-EX5 when the power is not turned on?
If the Sony Projector's power is not turning on, wait about 90 seconds before attempting to turn it on again, especially if it was recently turned off. Make sure that the lamp cover and the air filter cover are securely closed and attached.
What to do if Sony VPL-EX5 flashes red 6 times?
If the '/1' indicator flashes red six times on your Sony Projector, unplug the AC power cord from the wall outlet after the '/1' indicator goes out. Then, plug the power cord back into the wall outlet and turn the projector on again. If the '/1' flashes in red and the problem persists, the electrical system has failed.
What to do if my Sony VPL-EX5 has no picture?
If your Sony Projector shows no picture, ensure all cable connections are correct and securely connected. Verify that the input selection on the projector matches the source you're using. If the picture is muted, press the 'PIC MUTING' key to unmute it. Also, if you're using a computer, make sure its signal is set to output only to an external monitor.
How to fix a noisy picture on a Sony VPL-EX5?
To resolve a noisy picture on your Sony Projector, try changing the desktop pattern on the connected computer. The noise may appear depending on the combination of the number of dots input from the computer and the number of pixels on the LCD panel.
What to do if Sony VPL-EX5 picture is not clear?
If your Sony Projector's picture is not clear, start by adjusting the focus. If that doesn't work, condensation may have accumulated on the lens. Leave the projector on for about two hours to allow the condensation to clear.
How to stop Sony Projector picture from flickering?
If the picture on your Sony Projector flickers, adjust the 'Dot Phase' in the Input setting menu.
General| Projection distance | 1.1 - 10.5 m |
|---|---|
| Projection technology | LCD |
| Contrast ratio (typical) | 900:1 |
| Screen size compatibility | 300 \ |
| Projector native resolution | XGA (1024x768) |
| Keystone correction, vertical | -30 - 30 ° |
| Lamp power | 190 W |
| Light source type | Lamp |
| Service life of light source | 3000 h |
| Focus | Manual |
| Analog signal format system | PAL, SECAM |
| RMS rated power | 1 W |
| Number of built-in speakers | 1 |
| Resolution | 2359296 pixels |
| Dimensions (WxDxH) | 314 x 269 x 109 mm |
| Serial interface type | RS-232 |
| Plug and Play | Yes |
| Power consumption (standby) | 3 W |
| Power consumption (typical) | 260 W |
| Market positioning | Portable |
Weight and Dimensions| Weight | 3000 g |
|---|
Essential safety warnings regarding electrical shock, fire hazards, and proper grounding procedures.
Information on FCC compliance for digital devices, including interference limits and shielding requirements.
Important safety instructions covering electrical hazards, handling, and proper operation to prevent injury or damage.
Identifies unsuitable environments and locations that could cause projector malfunction or damage.
Ensuring proper air circulation around the projector to prevent internal heat build-up and maintain performance.
Highlights of the projector's capabilities, including image quality, power management, and lens design.
Description of security features like password protection and panel key locking for unauthorized operation prevention.
Identification and location of controls and indicators on the top, right side, and front of the projector.
Identification and location of connectors, vents, and other features on the rear and bottom of the projector.
Detailed explanation of each numbered component, including vents, lens, panel keys, connectors, and security features.
Instructions for turning the projector on/off and selecting the input source using the control panel keys.
Explanation of how to use the ENTER and arrow keys for navigating menus and making adjustments.
Details on connecting video and audio sources using the composite, S-Video, and stereo minijack inputs.
Information on connecting computers and other sources via RGB (D-sub) and audio inputs.
Explanation of various input, output, and remote control connectors for different models and signals.
Introduction to the remote commander, detailing the function of each key.
Detailed explanation of each button on the remote commander, including power, input, adjustment, and special function keys.
Guidelines and measurements for installing the projector, including throw distances for various screen sizes.
Steps to activate and use the projector's security lock feature with a password for protection.
Step-by-step guide for safely replacing the projector's lamp, including necessary precautions.
Detailed instructions on how to remove, wash, dry, and reattach the air filter for optimal projector performance.
Common power issues and their solutions, such as the projector not turning on or indicator light behavior.
Solutions for common picture problems including no image, noisy display, incorrect colors, or strange picture artifacts.
Detailed optical specifications including projection system, LCD panel resolution, lens details, lamp type, and throw distances.
Illustrative diagram showing measurements for floor installation, including distances from screen and adjusters.
Diagram and measurements for installing the projector on a ceiling, including required support and distances.
To Next Page
